diff options
Diffstat (limited to 'include/configs/km/km_arm.h')
| -rw-r--r-- | include/configs/km/km_arm.h | 54 |
1 files changed, 1 insertions, 53 deletions
diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h index a381a98470..d12d18770d 100644 --- a/include/configs/km/km_arm.h +++ b/include/configs/km/km_arm.h @@ -32,8 +32,6 @@ /* include common defines/options for all Keymile boards */ #include "keymile-common.h" -/* SPI NOR Flash default params, used by sf commands */ - /* Reserve 4 MB for malloc */ #define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024) @@ -43,15 +41,6 @@ #define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */ #define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */ -/* pseudo-non volatile RAM [hex] */ -#define CONFIG_KM_PNVRAM 0x80000 -/* physical RAM MTD size [hex] */ -#define CONFIG_KM_PHRAM 0x17F000 - -#define CONFIG_KM_CRAMFS_ADDR 0x2400000 -#define CONFIG_KM_KERNEL_ADDR 0x2000000 /* 3098KBytes */ -#define CONFIG_KM_FDT_ADDR 0x23E0000 /* 128KBytes */ - /* architecture specific default bootargs */ #define CONFIG_KM_DEF_BOOT_ARGS_CPU \ "bootcountaddr=${bootcountaddr} ${mtdparts}" \ @@ -72,26 +61,10 @@ #define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */ /* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK -#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE -#define CONFIG_SYS_NS16550_COM2 KW_UART1_BASE - -/* - * Serial Port configuration - * The following definitions let you select what serial you want to use - * for your console driver. - */ - -/* * For booting Linux, the board info and command line data * have to be in the first 8 MB of memory, since this is * the maximum mapped by the Linux kernel during initialization. */ -#define CONFIG_BOOTMAPSZ (8 << 20) /* Initial Memmap for Linux */ #define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */ #define CONFIG_INITRD_TAG /* enable INITRD tag */ #define CONFIG_SETUP_MEMORY_TAGS /* enable memory tag */ @@ -101,30 +74,17 @@ */ #define CONFIG_SYS_MAX_NAND_DEVICE 1 -#define BOOTFLASH_START 0x0 - -/* Kirkwood has two serial IF */ -#if (CONFIG_CONS_INDEX == 2) -#define CONFIG_KM_CONSOLE_TTY "ttyS1" -#else -#define CONFIG_KM_CONSOLE_TTY "ttyS0" -#endif - /* * Other required minimal configurations */ #define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */ -#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */ /* * Ethernet Driver configuration */ -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ +#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer autoneg timeout */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_PHY_BASE_ADR 0 -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_KM_COMMON_ETH_INIT /* standard km ethernet_present for piggy */ /* * I2C related stuff @@ -238,19 +198,9 @@ int get_scl(void); "arch=arm\0" \ "" -#if !defined(CONFIG_MTD_NOR_FLASH) -#undef CONFIG_JFFS2_CMDLINE -#endif - /* additions for new relocation code, must be added to all boards */ #define CONFIG_SYS_SDRAM_BASE 0x00000000 -/* Do early setups now in board_init_f() */ -/* - * resereved pram area at the end of memroy [hex] - * 8Mbytes for switch + 4Kbytes for bootcount - */ -#define CONFIG_KM_RESERVED_PRAM 0x801000 /* address for the bootcount (taken from end of RAM) */ #define BOOTCOUNT_ADDR (CONFIG_KM_RESERVED_PRAM) @@ -259,6 +209,4 @@ int get_scl(void); #define CONFIG_POST_SKIP_ENV_FLAGS #define CONFIG_POST_EXTERNAL_WORD_FUNCS -/* we do the whole PCIe FPGA config stuff here */ - #endif /* _CONFIG_KM_ARM_H */ |