diff options
| -rw-r--r-- | doc/device-tree-bindings/memory/ti,gpmc-child.yaml | 252 | ||||
| -rw-r--r-- | doc/device-tree-bindings/memory/ti,gpmc.yaml | 190 |
2 files changed, 442 insertions, 0 deletions
diff --git a/doc/device-tree-bindings/memory/ti,gpmc-child.yaml b/doc/device-tree-bindings/memory/ti,gpmc-child.yaml new file mode 100644 index 0000000000..8e541acdb1 --- /dev/null +++ b/doc/device-tree-bindings/memory/ti,gpmc-child.yaml @@ -0,0 +1,252 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc-child.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: device tree bindings for children of the Texas Instruments GPMC + +maintainers: + - Tony Lindgren <tony@atomide.com> + - Roger Quadros <rogerq@kernel.org> + +description: + This binding is meant for the child nodes of the GPMC node. The node + represents any device connected to the GPMC bus. It may be a Flash chip, + RAM chip or Ethernet controller, etc. These properties are meant for + configuring the GPMC settings/timings and will accompany the bindings + supported by the respective device. + +properties: + reg: true + +# GPMC Timing properties for child nodes. All are optional and default to 0. + gpmc,sync-clk-ps: + description: Minimum clock period for synchronous mode + default: 0 + +# Chip-select signal timings corresponding to GPMC_CONFIG2: + gpmc,cs-on-ns: + description: Assertion time + default: 0 + + gpmc,cs-rd-off-ns: + description: Read deassertion time + default: 0 + + gpmc,cs-wr-off-ns: + description: Write deassertion time + default: 0 + +# ADV signal timings corresponding to GPMC_CONFIG3: + gpmc,adv-on-ns: + description: Assertion time + default: 0 + + gpmc,adv-rd-off-ns: + description: Read deassertion time + default: 0 + + gpmc,adv-wr-off-ns: + description: Write deassertion time + default: 0 + + gpmc,adv-aad-mux-on-ns: + description: Assertion time for AAD + default: 0 + + gpmc,adv-aad-mux-rd-off-ns: + description: Read deassertion time for AAD + default: 0 + + gpmc,adv-aad-mux-wr-off-ns: + description: Write deassertion time for AAD + default: 0 + +# WE signals timings corresponding to GPMC_CONFIG4: + gpmc,we-on-ns: + description: Assertion time + default: 0 + + gpmc,we-off-ns: + description: Deassertion time + default: 0 + +# OE signals timings corresponding to GPMC_CONFIG4: + gpmc,oe-on-ns: + description: Assertion time + default: 0 + + gpmc,oe-off-ns: + description: Deassertion time + default: 0 + + gpmc,oe-aad-mux-on-ns: + description: Assertion time for AAD + default: 0 + + gpmc,oe-aad-mux-off-ns: + description: Deassertion time for AAD + default: 0 + +# Access time and cycle time timings (in nanoseconds) corresponding to +# GPMC_CONFIG5: + gpmc,page-burst-access-ns: + description: Multiple access word delay + default: 0 + + gpmc,access-ns: + description: Start-cycle to first data valid delay + default: 0 + + gpmc,rd-cycle-ns: + description: Total read cycle time + default: 0 + + gpmc,wr-cycle-ns: + description: Total write cycle time + default: 0 + + gpmc,bus-turnaround-ns: + description: Turn-around time between successive accesses + default: 0 + + gpmc,cycle2cycle-delay-ns: + description: Delay between chip-select pulses + default: 0 + + gpmc,clk-activation-ns: + description: GPMC clock activation time + default: 0 + + gpmc,wait-monitoring-ns: + description: Start of wait monitoring with regard to valid data + default: 0 + +# Boolean timing parameters. If property is present, parameter is enabled +# otherwise disabled. + gpmc,adv-extra-delay: + description: ADV signal is delayed by half GPMC clock + type: boolean + + gpmc,cs-extra-delay: + description: CS signal is delayed by half GPMC clock + type: boolean + + gpmc,cycle2cycle-diffcsen: + description: | + Add "cycle2cycle-delay" between successive accesses + to a different CS + type: boolean + + gpmc,cycle2cycle-samecsen: + description: | + Add "cycle2cycle-delay" between successive accesses + to the same CS + type: boolean + + gpmc,oe-extra-delay: + description: OE signal is delayed by half GPMC clock + type: boolean + + gpmc,we-extra-delay: + description: WE signal is delayed by half GPMC clock + type: boolean + + gpmc,time-para-granularity: + description: Multiply all access times by 2 + type: boolean + +# The following two properties are applicable only to OMAP3+ and AM335x: + gpmc,wr-access-ns: + description: | + In synchronous write mode, for single or + burst accesses, defines the number of + GPMC_FCLK cycles from start access time + to the GPMC_CLK rising edge used by the + memory device for the first data capture. + default: 0 + + gpmc,wr-data-mux-bus-ns: + description: | + In address-data multiplex mode, specifies + the time when the first data is driven on + the address-data bus. + default: 0 + +# GPMC chip-select settings properties for child nodes. All are optional. + gpmc,burst-length: + description: Page/burst length. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 4, 8, 16] + default: 0 + + gpmc,burst-wrap: + description: Enables wrap bursting + type: boolean + + gpmc,burst-read: + description: Enables read page/burst mode + type: boolean + + gpmc,burst-write: + description: Enables write page/burst mode + type: boolean + + gpmc,device-width: + description: | + Total width of device(s) connected to a GPMC + chip-select in bytes. The GPMC supports 8-bit + and 16-bit devices and so this property must be + 1 or 2. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2] + default: 1 + + gpmc,mux-add-data: + description: | + Address and data multiplexing configuration. + Valid values are + 0 for Non multiplexed mode + 1 for address-address-data multiplexing mode and + 2 for address-data multiplexing mode. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + + gpmc,sync-read: + description: | + Enables synchronous read. Defaults to asynchronous + is this is not set. + type: boolean + + gpmc,sync-write: + description: | + Enables synchronous writes. Defaults to asynchronous + is this is not set. + type: boolean + + gpmc,wait-pin: + description: | + Wait-pin used by client. Must be less than "gpmc,num-waitpins". + $ref: /schemas/types.yaml#/definitions/uint32 + + gpmc,wait-pin-polarity: + description: | + Set the desired polarity for the selected wait pin. + 0 for active low, 1 for active high. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1] + + gpmc,wait-on-read: + description: Enables wait monitoring on reads. + type: boolean + + gpmc,wait-on-write: + description: Enables wait monitoring on writes. + type: boolean + +required: + - reg + +# the GPMC child will have its own native properties +additionalProperties: true diff --git a/doc/device-tree-bindings/memory/ti,gpmc.yaml b/doc/device-tree-bindings/memory/ti,gpmc.yaml new file mode 100644 index 0000000000..e188a4bf75 --- /dev/null +++ b/doc/device-tree-bindings/memory/ti,gpmc.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/memory-controllers/ti,gpmc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Texas Instruments GPMC Memory Controller device-tree bindings + +maintainers: + - Tony Lindgren <tony@atomide.com> + - Roger Quadros <rogerq@kernel.org> + +description: + The GPMC is a unified memory controller dedicated for interfacing + with external memory devices like + - Asynchronous SRAM-like memories and ASICs + - Asynchronous, synchronous, and page mode burst NOR flash + - NAND flash + - Pseudo-SRAM devices + +properties: + compatible: + items: + - enum: + - ti,am3352-gpmc + - ti,am64-gpmc + - ti,omap2420-gpmc + - ti,omap2430-gpmc + - ti,omap3430-gpmc + - ti,omap4430-gpmc + + reg: + minItems: 1 + maxItems: 2 + + reg-names: + items: + - const: cfg + - const: data + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + description: | + Functional clock. Used for bus timing calculations and + GPMC configuration. + + clock-names: + items: + - const: fck + + power-domains: + maxItems: 1 + + dmas: + items: + - description: DMA channel for GPMC NAND prefetch + + dma-names: + items: + - const: rxtx + + "#address-cells": true + + "#size-cells": true + + gpmc,num-cs: + description: maximum number of supported chip-select lines. + $ref: /schemas/types.yaml#/definitions/uint32 + + gpmc,num-waitpins: + description: maximum number of supported wait pins. + $ref: /schemas/types.yaml#/definitions/uint32 + + ranges: + minItems: 1 + description: | + Must be set up to reflect the memory layout with four + integer values for each chip-select line in use, + <cs-number> 0 <physical address of mapping> <size> + items: + - description: NAND bank 0 + - description: NOR/SRAM bank 0 + - description: NOR/SRAM bank 1 + + '#interrupt-cells': + const: 2 + + interrupt-controller: + description: | + The GPMC driver implements and interrupt controller for + the NAND events "fifoevent" and "termcount" plus the + rising/falling edges on the GPMC_WAIT pins. + The interrupt number mapping is as follows + 0 - NAND_fifoevent + 1 - NAND_termcount + 2 - GPMC_WAIT0 pin edge + 3 - GPMC_WAIT1 pin edge, and so on. + + '#gpio-cells': + const: 2 + + gpio-controller: + description: | + The GPMC driver implements a GPIO controller for the + GPMC WAIT pins that can be used as general purpose inputs. + 0 maps to GPMC_WAIT0 pin. + + ti,hwmods: + description: + Name of the HWMOD associated with GPMC. This is for legacy + omap2/3 platforms only. + $ref: /schemas/types.yaml#/definitions/string + deprecated: true + + ti,no-idle-on-init: + description: + Prevent idling the module at init. This is for legacy omap2/3 + platforms only. + type: boolean + deprecated: true + +patternProperties: + "@[0-7],[a-f0-9]+$": + type: object + description: | + The child device node represents the device connected to the GPMC + bus. The device can be a NAND chip, SRAM device, NOR device + or an ASIC. + $ref: "ti,gpmc-child.yaml" + + +required: + - compatible + - reg + - gpmc,num-cs + - gpmc,num-waitpins + - "#address-cells" + - "#size-cells" + +allOf: + - if: + properties: + compatible: + contains: + const: ti,am64-gpmc + then: + required: + - reg-names + - power-domains + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/gpio/gpio.h> + + gpmc: memory-controller@50000000 { + compatible = "ti,am3352-gpmc"; + reg = <0x50000000 0x2000>; + interrupts = <100>; + clocks = <&l3s_clkctrl>; + clock-names = "fck"; + dmas = <&edma 52 0>; + dma-names = "rxtx"; + gpmc,num-cs = <8>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0 @addr 0x8000000, size 0x10000000 */ + interrupt-controller; + #interrupt-cells = <2>; + gpio-controller; + #gpio-cells = <2>; + + nand@0,0 { + compatible = "ti,omap2-nand"; + reg = <0 0 4>; + interrupt-parent = <&gpmc>; + interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */ + <1 IRQ_TYPE_NONE>; /* termcount */ + ti,nand-xfer-type = "prefetch-dma"; + ti,nand-ecc-opt = "bch16"; + ti,elm-id = <&elm>; + rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 pin */ + }; + }; |