Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (167 commits)
  OMAP4/5: Change omap4_sdp, omap4_panda, omap5_evm maintainer
  ARM: omap3: Add CONFIG_SPL_BOARD_INIT for CONFIG_SPL_MMC_SUPPORT
  ARM: omap3: Set SPL stack size to 8KB, image to 54KB.
  arm, omap3: fix warm reset serial output on OMAP36xx/AM/DM37xx
  OMAP4: Set fdt_high for OMAP4 devices to enable booting with Device Tree
  omap4: do not enable auxiliary cores
  omap4: do not enable fs-usb module
  omap4: panda: disable uart2 pads during boot
  igep00x0: change mpurate from 500 to auto
  igep00x0: enable the use of a plain text file
  tegra2: trivially enable 13 mhz crystal frequency
  tegra: Enable keyboard for Seaboard
  tegra: Switch on console mux and use environment for console
  tegra: Add tegra keyboard driver
  tegra: fdt: Add keyboard definitions for Seaboard
  tegra: fdt: Add keyboard controller definition
  tegra: Add keyboard support to funcmux
  input: Add support for keyboard matrix decoding from an fdt
  input: Add generic keyboard input handler
  input: Add linux/input.h for key code support
  fdt: Add fdtdec functions to read byte array
  tegra: Enable LP0 on Seaboard
  tegra: fdt: Add EMC data for Tegra2 Seaboard
  tegra: i2c: Add function to find DVC bus
  fdt: tegra: Add EMC node to device tree
  tegra: Add EMC settings for Seaboard
  tegra: Turn off power detect in board init
  tegra: Set up warmboot code on Nvidia boards
  tegra: Setup PMC scratch info from ap20 setup
  tegra: Add warmboot implementation
  tegra: Set up PMU for Nvidia boards
  tegra: Add PMU to manage power supplies
  tegra: Add EMC support for optimal memory timings
  tegra: Add header file for APB_MISC register
  tegra: Add tegra_get_chip_type() to detect SKU
  tegra: Add flow, gp_padctl, fuse, sdram headers
  tegra: Add crypto library for warmboot code
  tegra: Add functions to access low-level Osc/PLL details
  tegra: Move ap20.h header into arch location
  Add AES crypto library
  i2c: Add TPS6586X driver
  Add abs() macro to return absolute value
  fdt: Add function to return next compatible subnode
  fdt: Add function to locate an array in the device tree
  i.MX28: Avoid redefining serial_put[cs]()
  i.MX28: Check if WP detection is implemented at all
  i.MX28: Add battery boot components to SPL
  i.MX28: Reorder battery status functions in SPL
  i.MX28: Add LRADC init to i.MX28 SPL
  i.MX28: Add LRADC register definitions
  i.MX28: Shut down the LCD controller before reset
  i.MX28: Add LCDIF register definitions
  i.MX28: Implement boot pads sampling and reporting
  i.MX28: Improve passing of data from SPL to U-Boot
  M28EVK: Add SD update command
  M28EVK: Implement support for new board V2.0
  FEC: Abstract out register setup
  MX5: PAD_CTL_DRV_VOT_LOW and PAD_CTL_DRV_VOT_HIGH exchanged
  i.MX28: Add delay after CPU bypass is cleared
  spi: mxs: Allow other chip selects to work
  spi: mxs: Introduce spi_cs_is_valid()
  mx53loco: Remove unneeded gpio_set_value()
  mx53loco: Add CONFIG_REVISION_TAG
  mx53loco: Turn on VUSB regulator
  mx53loco: Add mc34708 support and set mx53 frequency at 1GHz
  pmic: dialog: Avoid name conflicts
  imx: Add u-boot.imx as target for ARM9 i.MX SOCs
  i.MX2: Include asm/types.h in arch-mx25/imx-regs.h
  imx: usb: There is no such register
  i.MX25: usb: Set PORTSCx register
  imx: nand: Support flash based BBT
  i.MX25: This architecture has a GPIO4 too
  i.MX25: esdhc: Add mxc_get_clock infrastructure
  i.MX6: mx6q_sabrelite: add SATA bindings
  i.MX6: add enable_sata_clock()
  i.MX6: Add ANATOP regulator init
  mx28evk: add NAND support
  USB: ehci-mx6: Fix broken IO access
  M28: Scan only first 512 MB of DRAM to avoid memory wraparound
  Revert "i.MX28: Enable additional DRAM address bits"
  M28: Enable FDT support
  mx53loco: Add support for 1GHz operation for DA9053-based boards
  mx53loco: Allow to print CPU information at a later stage
  mx5: Add clock config interface
  imx-common: Factor out get_ahb_clk()
  i.MX6Q: mx6qsabrelite: Add keypress support to alter boot flow
  mx31pdk: Allow booting a zImage kernel
  mx6qarm2: Allow booting a zImage kernel
  mx6qsabrelite: Allow booting a zImage kernel
  mx28evk: Allow booting a zImage kernel
  m28evk: Allow to booting a dt kernel
  mx28evk: Allow to booting a dt kernel
  mx6qsabrelite: No need to set the direction for GPIO3_23 again
  pmic: Add support for the Dialog DA9053 PMIC
  MX53: mx53loco: Add SATA support
  MX53: Add support to ESG ima3 board
  SATA: add driver for MX5 / MX6 SOCs
  MX53: add function to set SATA clock to internal
  SATA: check for return value from sata functions
  MX5: Add definitions for SATA controller
  NET: fec_mxc.c: Add a way to disable auto negotiation
  Define UART4 and UART5 base addresses
  EXYNOS: Change bits per pixel value proper for u-boot.
  EXYNOS: support TRATS board display function
  LCD: support S6E8AX0 amoled driver based on EXYNOS MIPI DSI
  EXYNOS: support EXYNOS MIPI DSI interface driver.
  EXYNOS: support EXYNOS framebuffer and FIMD display drivers.
  LCD: add data structure for EXYNOS display driver
  EXYNOS: add LCD and MIPI DSI clock interface.
  EXYNOS: definitions of system resgister and power management registers.
  SMDK5250: fix compiler warning
  misc:pmic:samsung Convert TRATS target to use MAX8997 instead of MAX8998
  misc:pmic:max8997 MAX8997 support for PMIC driver
  TRATS: modify the trats's configuration
  ARM: Exynos4: ADC: Universal_C210: Enable LDO4 power line for ADC measurement
  EXYNOS: Rename exynos5_tzpc structure to exynos_tzpc
  arm: ea20: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  arm: cam_enc_4xx: Change macro from BOARD_LATE_INIT to CONFIG_BOARD_LATE_INIT
  cm-t35: add I2C multi-bus support
  include/configs: Remove CONFIG_SYS_64BIT_STRTOUL
  include/configs: Remove CONFIG_SYS_64BIT_VSPRINTF
  omap3: Introduce weak misc_init_r
  omap730p2: Remove empty misc_init_r
  omap5912osk: Remove empty misc_init_r
  omap4+: Remove CONFIG_ARCH_CPU_INIT
  omap4: Remove CONFIG_SYS_MMC_SET_DEV
  OMAP3: pandora: drop console kernel argument
  OMAP3: pandora: revise GPIO configuration
  ...

1 files changed, 472 insertions, 21 deletions

diff --git a/arch/arm/cpu/armv7/mx5/clock.c b/arch/arm/cpu/armv7/mx5/clock.c
index e92f10623a..fc2406bcad 100644
--- a/arch/arm/cpu/armv7/mx5/clock.c
+++ b/arch/arm/cpu/armv7/mx5/clock.c
@@ -30,6 +30,7 @@
 #include <asm/arch/crm_regs.h>
 #include <asm/arch/clock.h>
 #include <div64.h>
+#include <asm/arch/sys_proto.h>
 
 enum pll_clocks {
 	PLL1_CLOCK = 0,
@@ -48,6 +49,42 @@ struct mxc_pll_reg *mxc_plls[PLL_CLOCKS] = {
 #endif
 };
 
+#define AHB_CLK_ROOT    133333333
+#define SZ_DEC_1M       1000000
+#define PLL_PD_MAX      16      /* Actual pd+1 */
+#define PLL_MFI_MAX     15
+#define PLL_MFI_MIN     5
+#define ARM_DIV_MAX     8
+#define IPG_DIV_MAX     4
+#define AHB_DIV_MAX     8
+#define EMI_DIV_MAX     8
+#define NFC_DIV_MAX     8
+
+#define MX5_CBCMR	0x00015154
+#define MX5_CBCDR	0x02888945
+
+struct fixed_pll_mfd {
+	u32 ref_clk_hz;
+	u32 mfd;
+};
+
+const struct fixed_pll_mfd fixed_mfd[] = {
+	{CONFIG_SYS_MX5_HCLK, 24 * 16},
+};
+
+struct pll_param {
+	u32 pd;
+	u32 mfi;
+	u32 mfn;
+	u32 mfd;
+};
+
+#define PLL_FREQ_MAX(ref_clk)  (4 * (ref_clk) * PLL_MFI_MAX)
+#define PLL_FREQ_MIN(ref_clk) \
+		((2 * (ref_clk) * (PLL_MFI_MIN - 1)) / PLL_PD_MAX)
+#define MAX_DDR_CLK     420000000
+#define NFC_CLK_MAX     34000000
+
 struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE;
 
 void set_usboh3_clk(void)
@@ -192,7 +229,7 @@ u32 get_mcu_main_clk(void)
 /*
  * Get the rate of peripheral's root clock.
  */
-static u32 get_periph_clk(void)
+u32 get_periph_clk(void)
 {
 	u32 reg;
 
@@ -213,22 +250,6 @@ static u32 get_periph_clk(void)
 }
 
 /*
- * Get the rate of ahb clock.
- */
-static u32 get_ahb_clk(void)
-{
-	uint32_t freq, div, reg;
-
-	freq = get_periph_clk();
-
-	reg = __raw_readl(&mxc_ccm->cbcdr);
-	div = ((reg & MXC_CCM_CBCDR_AHB_PODF_MASK) >>
-			MXC_CCM_CBCDR_AHB_PODF_OFFSET) + 1;
-
-	return freq / div;
-}
-
-/*
  * Get the rate of ipg clock.
  */
 static u32 get_ipg_clk(void)
@@ -306,7 +327,7 @@ static u32 get_uart_clk(void)
 /*
  * This function returns the low power audio clock.
  */
-u32 get_lp_apm(void)
+static u32 get_lp_apm(void)
 {
 	u32 ret_val = 0;
 	u32 ccsr = __raw_readl(&mxc_ccm->ccsr);
@@ -322,7 +343,7 @@ u32 get_lp_apm(void)
 /*
  * get cspi clock rate.
  */
-u32 imx_get_cspiclk(void)
+static u32 imx_get_cspiclk(void)
 {
 	u32 ret_val = 0, pdf, pre_pdf, clk_sel;
 	u32 cscmr1 = __raw_readl(&mxc_ccm->cscmr1);
@@ -359,8 +380,77 @@ u32 imx_get_cspiclk(void)
 	return ret_val;
 }
 
+static u32 get_axi_a_clk(void)
+{
+	u32 cbcdr =  __raw_readl(&mxc_ccm->cbcdr);
+	u32 pdf = (cbcdr & MXC_CCM_CBCDR_AXI_A_PODF_MASK) \
+			>> MXC_CCM_CBCDR_AXI_A_PODF_OFFSET;
+
+	return  get_periph_clk() / (pdf + 1);
+}
+
+static u32 get_axi_b_clk(void)
+{
+	u32 cbcdr =  __raw_readl(&mxc_ccm->cbcdr);
+	u32 pdf = (cbcdr & MXC_CCM_CBCDR_AXI_B_PODF_MASK) \
+			>> MXC_CCM_CBCDR_AXI_B_PODF_OFFSET;
+
+	return  get_periph_clk() / (pdf + 1);
+}
+
+static u32 get_emi_slow_clk(void)
+{
+	u32 cbcdr = __raw_readl(&mxc_ccm->cbcdr);
+	u32 emi_clk_sel = cbcdr & MXC_CCM_CBCDR_EMI_CLK_SEL;
+	u32 pdf = (cbcdr & MXC_CCM_CBCDR_EMI_PODF_MASK) \
+			>> MXC_CCM_CBCDR_EMI_PODF_OFFSET;
+
+	if (emi_clk_sel)
+		return  get_ahb_clk() / (pdf + 1);
+
+	return  get_periph_clk() / (pdf + 1);
+}
+
+static u32 get_ddr_clk(void)
+{
+	u32 ret_val = 0;
+	u32 cbcmr = __raw_readl(&mxc_ccm->cbcmr);
+	u32 ddr_clk_sel = (cbcmr & MXC_CCM_CBCMR_DDR_CLK_SEL_MASK) \
+				>> MXC_CCM_CBCMR_DDR_CLK_SEL_OFFSET;
+#ifdef CONFIG_MX51
+	u32 cbcdr = __raw_readl(&mxc_ccm->cbcdr);
+	if (cbcdr & MXC_CCM_CBCDR_DDR_HIFREQ_SEL) {
+		u32 ddr_clk_podf = (cbcdr & MXC_CCM_CBCDR_DDR_PODF_MASK) >> \
+					MXC_CCM_CBCDR_DDR_PODF_OFFSET;
+
+		ret_val = decode_pll(mxc_plls[PLL1_CLOCK], CONFIG_SYS_MX5_HCLK);
+		ret_val /= ddr_clk_podf + 1;
+
+		return ret_val;
+	}
+#endif
+	switch (ddr_clk_sel) {
+	case 0:
+		ret_val = get_axi_a_clk();
+		break;
+	case 1:
+		ret_val = get_axi_b_clk();
+		break;
+	case 2:
+		ret_val = get_emi_slow_clk();
+		break;
+	case 3:
+		ret_val = get_ahb_clk();
+		break;
+	default:
+		break;
+	}
+
+	return ret_val;
+}
+
 /*
- * The API of get mxc clockes.
+ * The API of get mxc clocks.
  */
 unsigned int mxc_get_clock(enum mxc_clock clk)
 {
@@ -380,10 +470,14 @@ unsigned int mxc_get_clock(enum mxc_clock clk)
 	case MXC_FEC_CLK:
 		return decode_pll(mxc_plls[PLL1_CLOCK],
 				    CONFIG_SYS_MX5_HCLK);
+	case MXC_SATA_CLK:
+		return get_ahb_clk();
+	case MXC_DDR_CLK:
+		return get_ddr_clk();
 	default:
 		break;
 	}
-	return -1;
+	return -EINVAL;
 }
 
 u32 imx_get_uartclk(void)
@@ -397,6 +491,362 @@ u32 imx_get_fecclk(void)
 	return mxc_get_clock(MXC_IPG_CLK);
 }
 
+static int gcd(int m, int n)
+{
+	int t;
+	while (m > 0) {
+		if (n > m) {
+			t = m;
+			m = n;
+			n = t;
+		} /* swap */
+		m -= n;
+	}
+	return n;
+}
+
+/*
+ * This is to calculate various parameters based on reference clock and
+ * targeted clock based on the equation:
+ *      t_clk = 2*ref_freq*(mfi + mfn/(mfd+1))/(pd+1)
+ * This calculation is based on a fixed MFD value for simplicity.
+ */
+static int calc_pll_params(u32 ref, u32 target, struct pll_param *pll)
+{
+	u64 pd, mfi = 1, mfn, mfd, t1;
+	u32 n_target = target;
+	u32 n_ref = ref, i;
+
+	/*
+	 * Make sure targeted freq is in the valid range.
+	 * Otherwise the following calculation might be wrong!!!
+	 */
+	if (n_target < PLL_FREQ_MIN(ref) ||
+		n_target > PLL_FREQ_MAX(ref)) {
+		printf("Targeted peripheral clock should be"
+			"within [%d - %d]\n",
+			PLL_FREQ_MIN(ref) / SZ_DEC_1M,
+			PLL_FREQ_MAX(ref) / SZ_DEC_1M);
+		return -EINVAL;
+	}
+
+	for (i = 0; i < ARRAY_SIZE(fixed_mfd); i++) {
+		if (fixed_mfd[i].ref_clk_hz == ref) {
+			mfd = fixed_mfd[i].mfd;
+			break;
+		}
+	}
+
+	if (i == ARRAY_SIZE(fixed_mfd))
+		return -EINVAL;
+
+	/* Use n_target and n_ref to avoid overflow */
+	for (pd = 1; pd <= PLL_PD_MAX; pd++) {
+		t1 = n_target * pd;
+		do_div(t1, (4 * n_ref));
+		mfi = t1;
+		if (mfi > PLL_MFI_MAX)
+			return -EINVAL;
+		else if (mfi < 5)
+			continue;
+		break;
+	}
+	/*
+	 * Now got pd and mfi already
+	 *
+	 * mfn = (((n_target * pd) / 4 - n_ref * mfi) * mfd) / n_ref;
+	 */
+	t1 = n_target * pd;
+	do_div(t1, 4);
+	t1 -= n_ref * mfi;
+	t1 *= mfd;
+	do_div(t1, n_ref);
+	mfn = t1;
+	debug("ref=%d, target=%d, pd=%d," "mfi=%d,mfn=%d, mfd=%d\n",
+		ref, n_target, (u32)pd, (u32)mfi, (u32)mfn, (u32)mfd);
+	i = 1;
+	if (mfn != 0)
+		i = gcd(mfd, mfn);
+	pll->pd = (u32)pd;
+	pll->mfi = (u32)mfi;
+	do_div(mfn, i);
+	pll->mfn = (u32)mfn;
+	do_div(mfd, i);
+	pll->mfd = (u32)mfd;
+
+	return 0;
+}
+
+#define calc_div(tgt_clk, src_clk, limit) ({		\
+		u32 v = 0;				\
+		if (((src_clk) % (tgt_clk)) <= 100)	\
+			v = (src_clk) / (tgt_clk);	\
+		else					\
+			v = ((src_clk) / (tgt_clk)) + 1;\
+		if (v > limit)				\
+			v = limit;			\
+		(v - 1);				\
+	})
+
+#define CHANGE_PLL_SETTINGS(pll, pd, fi, fn, fd) \
+	{	\
+		__raw_writel(0x1232, &pll->ctrl);		\
+		__raw_writel(0x2, &pll->config);		\
+		__raw_writel((((pd) - 1) << 0) | ((fi) << 4),	\
+			&pll->op);				\
+		__raw_writel(fn, &(pll->mfn));			\
+		__raw_writel((fd) - 1, &pll->mfd);		\
+		__raw_writel((((pd) - 1) << 0) | ((fi) << 4),	\
+			&pll->hfs_op);				\
+		__raw_writel(fn, &pll->hfs_mfn);		\
+		__raw_writel((fd) - 1, &pll->hfs_mfd);		\
+		__raw_writel(0x1232, &pll->ctrl);		\
+		while (!__raw_readl(&pll->ctrl) & 0x1)		\
+			;\
+	}
+
+static int config_pll_clk(enum pll_clocks index, struct pll_param *pll_param)
+{
+	u32 ccsr = __raw_readl(&mxc_ccm->ccsr);
+	struct mxc_pll_reg *pll = mxc_plls[index];
+
+	switch (index) {
+	case PLL1_CLOCK:
+		/* Switch ARM to PLL2 clock */
+		__raw_writel(ccsr | 0x4, &mxc_ccm->ccsr);
+		CHANGE_PLL_SETTINGS(pll, pll_param->pd,
+					pll_param->mfi, pll_param->mfn,
+					pll_param->mfd);
+		/* Switch back */
+		__raw_writel(ccsr & ~0x4, &mxc_ccm->ccsr);
+		break;
+	case PLL2_CLOCK:
+		/* Switch to pll2 bypass clock */
+		__raw_writel(ccsr | 0x2, &mxc_ccm->ccsr);
+		CHANGE_PLL_SETTINGS(pll, pll_param->pd,
+					pll_param->mfi, pll_param->mfn,
+					pll_param->mfd);
+		/* Switch back */
+		__raw_writel(ccsr & ~0x2, &mxc_ccm->ccsr);
+		break;
+	case PLL3_CLOCK:
+		/* Switch to pll3 bypass clock */
+		__raw_writel(ccsr | 0x1, &mxc_ccm->ccsr);
+		CHANGE_PLL_SETTINGS(pll, pll_param->pd,
+					pll_param->mfi, pll_param->mfn,
+					pll_param->mfd);
+		/* Switch back */
+		__raw_writel(ccsr & ~0x1, &mxc_ccm->ccsr);
+		break;
+	case PLL4_CLOCK:
+		/* Switch to pll4 bypass clock */
+		__raw_writel(ccsr | 0x20, &mxc_ccm->ccsr);
+		CHANGE_PLL_SETTINGS(pll, pll_param->pd,
+					pll_param->mfi, pll_param->mfn,
+					pll_param->mfd);
+		/* Switch back */
+		__raw_writel(ccsr & ~0x20, &mxc_ccm->ccsr);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/* Config CPU clock */
+static int config_core_clk(u32 ref, u32 freq)
+{
+	int ret = 0;
+	struct pll_param pll_param;
+
+	memset(&pll_param, 0, sizeof(struct pll_param));
+
+	/* The case that periph uses PLL1 is not considered here */
+	ret = calc_pll_params(ref, freq, &pll_param);
+	if (ret != 0) {
+		printf("Error:Can't find pll parameters: %d\n", ret);
+		return ret;
+	}
+
+	return config_pll_clk(PLL1_CLOCK, &pll_param);
+}
+
+static int config_nfc_clk(u32 nfc_clk)
+{
+	u32 reg;
+	u32 parent_rate = get_emi_slow_clk();
+	u32 div = parent_rate / nfc_clk;
+
+	if (nfc_clk <= 0)
+		return -EINVAL;
+	if (div == 0)
+		div++;
+	if (parent_rate / div > NFC_CLK_MAX)
+		div++;
+	reg = __raw_readl(&mxc_ccm->cbcdr);
+	reg &= ~MXC_CCM_CBCDR_NFC_PODF_MASK;
+	reg |= (div - 1) << MXC_CCM_CBCDR_NFC_PODF_OFFSET;
+	__raw_writel(reg, &mxc_ccm->cbcdr);
+	while (__raw_readl(&mxc_ccm->cdhipr) != 0)
+		;
+	return 0;
+}
+
+/* Config main_bus_clock for periphs */
+static int config_periph_clk(u32 ref, u32 freq)
+{
+	int ret = 0;
+	struct pll_param pll_param;
+
+	memset(&pll_param, 0, sizeof(struct pll_param));
+
+	if (__raw_readl(&mxc_ccm->cbcdr) & MXC_CCM_CBCDR_PERIPH_CLK_SEL) {
+		ret = calc_pll_params(ref, freq, &pll_param);
+		if (ret != 0) {
+			printf("Error:Can't find pll parameters: %d\n",
+				ret);
+			return ret;
+		}
+		switch ((__raw_readl(&mxc_ccm->cbcmr) & \
+			MXC_CCM_CBCMR_PERIPH_CLK_SEL_MASK) >> \
+			MXC_CCM_CBCMR_PERIPH_CLK_SEL_OFFSET) {
+		case 0:
+			return config_pll_clk(PLL1_CLOCK, &pll_param);
+			break;
+		case 1:
+			return config_pll_clk(PLL3_CLOCK, &pll_param);
+			break;
+		default:
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static int config_ddr_clk(u32 emi_clk)
+{
+	u32 clk_src;
+	s32 shift = 0, clk_sel, div = 1;
+	u32 cbcmr = __raw_readl(&mxc_ccm->cbcmr);
+	u32 cbcdr = __raw_readl(&mxc_ccm->cbcdr);
+
+	if (emi_clk > MAX_DDR_CLK) {
+		printf("Warning:DDR clock should not exceed %d MHz\n",
+			MAX_DDR_CLK / SZ_DEC_1M);
+		emi_clk = MAX_DDR_CLK;
+	}
+
+	clk_src = get_periph_clk();
+	/* Find DDR clock input */
+	clk_sel = (cbcmr >> 10) & 0x3;
+	switch (clk_sel) {
+	case 0:
+		shift = 16;
+		break;
+	case 1:
+		shift = 19;
+		break;
+	case 2:
+		shift = 22;
+		break;
+	case 3:
+		shift = 10;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	if ((clk_src % emi_clk) < 10000000)
+		div = clk_src / emi_clk;
+	else
+		div = (clk_src / emi_clk) + 1;
+	if (div > 8)
+		div = 8;
+
+	cbcdr = cbcdr & ~(0x7 << shift);
+	cbcdr |= ((div - 1) << shift);
+	__raw_writel(cbcdr, &mxc_ccm->cbcdr);
+	while (__raw_readl(&mxc_ccm->cdhipr) != 0)
+		;
+	__raw_writel(0x0, &mxc_ccm->ccdr);
+
+	return 0;
+}
+
+/*
+ * This function assumes the expected core clock has to be changed by
+ * modifying the PLL. This is NOT true always but for most of the times,
+ * it is. So it assumes the PLL output freq is the same as the expected
+ * core clock (presc=1) unless the core clock is less than PLL_FREQ_MIN.
+ * In the latter case, it will try to increase the presc value until
+ * (presc*core_clk) is greater than PLL_FREQ_MIN. It then makes call to
+ * calc_pll_params() and obtains the values of PD, MFI,MFN, MFD based
+ * on the targeted PLL and reference input clock to the PLL. Lastly,
+ * it sets the register based on these values along with the dividers.
+ * Note 1) There is no value checking for the passed-in divider values
+ *         so the caller has to make sure those values are sensible.
+ *      2) Also adjust the NFC divider such that the NFC clock doesn't
+ *         exceed NFC_CLK_MAX.
+ *      3) IPU HSP clock is independent of AHB clock. Even it can go up to
+ *         177MHz for higher voltage, this function fixes the max to 133MHz.
+ *      4) This function should not have allowed diag_printf() calls since
+ *         the serial driver has been stoped. But leave then here to allow
+ *         easy debugging by NOT calling the cyg_hal_plf_serial_stop().
+ */
+int mxc_set_clock(u32 ref, u32 freq, enum mxc_clock clk)
+{
+	freq *= SZ_DEC_1M;
+
+	switch (clk) {
+	case MXC_ARM_CLK:
+		if (config_core_clk(ref, freq))
+			return -EINVAL;
+		break;
+	case MXC_PERIPH_CLK:
+		if (config_periph_clk(ref, freq))
+			return -EINVAL;
+		break;
+	case MXC_DDR_CLK:
+		if (config_ddr_clk(freq))
+			return -EINVAL;
+		break;
+	case MXC_NFC_CLK:
+		if (config_nfc_clk(freq))
+			return -EINVAL;
+		break;
+	default:
+		printf("Warning:Unsupported or invalid clock type\n");
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_MX53
+/*
+ * The clock for the external interface can be set to use internal clock
+ * if fuse bank 4, row 3, bit 2 is set.
+ * This is an undocumented feature and it was confirmed by Freescale's support:
+ * Fuses (but not pins) may be used to configure SATA clocks.
+ * Particularly the i.MX53 Fuse_Map contains the next information
+ * about configuring SATA clocks :  SATA_ALT_REF_CLK[1:0] (offset 0x180C)
+ * '00' - 100MHz (External)
+ * '01' - 50MHz (External)
+ * '10' - 120MHz, internal (USB PHY)
+ * '11' - Reserved
+*/
+void mxc_set_sata_internal_clock(void)
+{
+	u32 *tmp_base =
+		(u32 *)(IIM_BASE_ADDR + 0x180c);
+
+	set_usb_phy1_clk();
+
+	writel((readl(tmp_base) & (~0x7)) | 0x4, tmp_base);
+}
+#endif
+
 /*
  * Dump some core clockes.
  */
@@ -419,6 +869,7 @@ int do_mx5_showclocks(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
 	printf("AHB        %8d kHz\n", mxc_get_clock(MXC_AHB_CLK) / 1000);
 	printf("IPG        %8d kHz\n", mxc_get_clock(MXC_IPG_CLK) / 1000);
 	printf("IPG PERCLK %8d kHz\n", mxc_get_clock(MXC_IPG_PERCLK) / 1000);
+	printf("DDR        %8d kHz\n", mxc_get_clock(MXC_DDR_CLK) / 1000);
 
 	return 0;
 }