From a897269c932999a5c028654489ad68baa6806fdb Mon Sep 17 00:00:00 2001 From: Anup Patel Date: Mon, 8 Jul 2019 04:10:55 +0000 Subject: cmd: Remove mmc_spi command The mmc_spi command was added to manually setup MMC over SPI bus using command. This was required by the legacy non-DM MMC_SPI driver. With DM based MMC_SPI driver in-place, we can now use all general storge commands and mmc command for MMC over SPI bus hence we remove the mmc_spi command all it's references. Suggested-by: Bin Meng Signed-off-by: Anup Patel Reviewed-by: Bin Meng --- cmd/mmc_spi.c | 88 ----------------------------------------------------------- 1 file changed, 88 deletions(-) delete mode 100644 cmd/mmc_spi.c (limited to 'cmd/mmc_spi.c') diff --git a/cmd/mmc_spi.c b/cmd/mmc_spi.c deleted file mode 100644 index 0c44d06817..0000000000 --- a/cmd/mmc_spi.c +++ /dev/null @@ -1,88 +0,0 @@ -/* - * Command for mmc_spi setup. - * - * Copyright (C) 2010 Thomas Chou - * Licensed under the GPL-2 or later. - */ - -#include -#include -#include - -#ifndef CONFIG_MMC_SPI_BUS -# define CONFIG_MMC_SPI_BUS 0 -#endif -#ifndef CONFIG_MMC_SPI_CS -# define CONFIG_MMC_SPI_CS 1 -#endif -/* in SPI mode, MMC speed limit is 20MHz, while SD speed limit is 25MHz */ -#ifndef CONFIG_MMC_SPI_SPEED -# define CONFIG_MMC_SPI_SPEED 25000000 -#endif -/* MMC and SD specs only seem to care that sampling is on the - * rising edge ... meaning SPI modes 0 or 3. So either SPI mode - * should be legit. We'll use mode 0 since the steady state is 0, - * which is appropriate for hotplugging, unless the platform data - * specify mode 3 (if hardware is not compatible to mode 0). - */ -#ifndef CONFIG_MMC_SPI_MODE -# define CONFIG_MMC_SPI_MODE SPI_MODE_0 -#endif - -static int do_mmc_spi(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) -{ - uint bus = CONFIG_MMC_SPI_BUS; - uint cs = CONFIG_MMC_SPI_CS; - uint speed = CONFIG_MMC_SPI_SPEED; - uint mode = CONFIG_MMC_SPI_MODE; - char *endp; - struct mmc *mmc; - - if (argc < 2) - goto usage; - - cs = simple_strtoul(argv[1], &endp, 0); - if (*argv[1] == 0 || (*endp != 0 && *endp != ':')) - goto usage; - if (*endp == ':') { - if (endp[1] == 0) - goto usage; - bus = cs; - cs = simple_strtoul(endp + 1, &endp, 0); - if (*endp != 0) - goto usage; - } - if (argc >= 3) { - speed = simple_strtoul(argv[2], &endp, 0); - if (*argv[2] == 0 || *endp != 0) - goto usage; - } - if (argc >= 4) { - mode = simple_strtoul(argv[3], &endp, 16); - if (*argv[3] == 0 || *endp != 0) - goto usage; - } - if (!spi_cs_is_valid(bus, cs)) { - printf("Invalid SPI bus %u cs %u\n", bus, cs); - return 1; - } - - mmc = mmc_spi_init(bus, cs, speed, mode); - if (!mmc) { - printf("Failed to create MMC Device\n"); - return 1; - } - printf("%s: %d at %u:%u hz %u mode %u\n", mmc->cfg->name, - mmc->block_dev.devnum, bus, cs, speed, mode); - mmc_init(mmc); - return 0; - -usage: - return CMD_RET_USAGE; -} - -U_BOOT_CMD( - mmc_spi, 4, 0, do_mmc_spi, - "mmc_spi setup", - "[bus:]cs [hz] [mode] - setup mmc_spi device" -); -- cgit v1.2.3