diff options
Diffstat (limited to 'include/configs')
26 files changed, 727 insertions, 99 deletions
diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h index c15bbd856c..a823f9f3a7 100644 --- a/include/configs/B4860QDS.h +++ b/include/configs/B4860QDS.h @@ -34,6 +34,15 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc #endif +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +/* Set 1M boot space */ +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_NO_FLASH +#endif + /* High Level Configuration Options */ #define CONFIG_BOOKE #define CONFIG_E500 /* BOOKE e500 family */ @@ -63,6 +72,7 @@ #define CONFIG_SYS_SRIO #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ +#define CONFIG_SRIO_PCIE_BOOT_MASTER #endif #define CONFIG_FSL_LAW /* Use common FSL init code */ @@ -84,14 +94,15 @@ #define CONFIG_ENV_OVERWRITE #ifdef CONFIG_SYS_NO_FLASH +#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) #define CONFIG_ENV_IS_NOWHERE +#endif #else #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #endif -#ifndef CONFIG_SYS_NO_FLASH #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH @@ -113,16 +124,18 @@ #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +#define CONFIG_ENV_IS_IN_REMOTE +#define CONFIG_ENV_ADDR 0xffe20000 +#define CONFIG_ENV_SIZE 0x2000 +#elif defined(CONFIG_ENV_IS_NOWHERE) +#define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #endif -#else /* CONFIG_SYS_NO_FLASH */ -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ -#endif #ifndef __ASSEMBLY__ unsigned long get_board_sys_clk(void); @@ -223,7 +236,7 @@ unsigned long get_board_ddr_clk(void); /* NOR Flash Timing Params */ #define CONFIG_SYS_NOR_CSOR CSOR_NOR_ADM_SHIFT(4) #define CONFIG_SYS_NOR_FTIM0 (FTIM0_NOR_TACSE(0x01) | \ - FTIM0_NOR_TEADC(0x01) | \ + FTIM0_NOR_TEADC(0x04) | \ FTIM0_NOR_TEAHC(0x20)) #define CONFIG_SYS_NOR_FTIM1 (FTIM1_NOR_TACO(0x35) | \ FTIM1_NOR_TRAD_NOR(0x1A) |\ @@ -600,6 +613,16 @@ unsigned long get_board_ddr_clk(void); #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +/* + * Slave has no ucode locally, it can fetch this from remote. When implementing + * in two corenet boards, slave's ucode could be stored in master's memory + * space, the address can be mapped from slave TLB->slave LAW-> + * slave SRIO or PCIE outbound window->master inbound window-> + * master LAW->the ucode address in master's memory space. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h index fd076e09a2..b5911c6945 100644 --- a/include/configs/BSC9131RDB.h +++ b/include/configs/BSC9131RDB.h @@ -40,10 +40,34 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif -#ifndef CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#ifdef CONFIG_NAND +#define CONFIG_SPL +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" + +#define CONFIG_SYS_TEXT_BASE 0x00201000 +#define CONFIG_SPL_TEXT_BASE 0xFFFFE000 +#define CONFIG_SPL_MAX_SIZE 8192 +#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 +#define CONFIG_SPL_RELOC_STACK 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" #endif +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + + /* High Level Configuration Options */ #define CONFIG_BOOKE /* BOOKE */ #define CONFIG_E500 /* BOOKE e500 family */ @@ -55,7 +79,11 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on 9131 RDB */ +#if defined(CONFIG_SYS_CLK_100) +#define CONFIG_SYS_CLK_FREQ 100000000 /* SYSCLK for 9131 RDB */ +#else #define CONFIG_SYS_CLK_FREQ 66666666 /* SYSCLK for 9131 RDB */ +#endif #define CONFIG_HWCONFIG /* @@ -125,16 +153,21 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses */ /* CONFIG_SYS_IMMR */ +/* DSP CCSRBAR */ +#define CONFIG_SYS_FSL_DSP_CCSRBAR CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT +#define CONFIG_SYS_FSL_DSP_CCSRBAR_PHYS CONFIG_SYS_FSL_DSP_CCSRBAR_DEFAULT /* * Memory map * * 0x0000_0000 0x3FFF_FFFF DDR 1G cacheable * 0x8800_0000 0x8810_0000 IFC internal SRAM 1M + * 0xB000_0000 0xB0FF_FFFF DSP core M2 memory 16M * 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M * 0xC1F0_0000 0xC1F3_FFFF PA L2 SRAM Region 0 256K * 0xC1F8_0000 0xC1F9_FFFF PA L2 SRAM Region 1 128K * 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K + * 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M * 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M * 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND flash buffer 8M * @@ -214,6 +247,9 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#ifdef CONFIG_SPL_BUILD +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ @@ -295,7 +331,6 @@ extern unsigned long get_sdram_size(void); /* * Environment */ -#if defined(CONFIG_SYS_RAMBOOT) #if defined(CONFIG_RAMBOOT_SPIFLASH) #define CONFIG_ENV_IS_IN_SPI_FLASH #define CONFIG_ENV_SPI_BUS 0 @@ -305,15 +340,16 @@ extern unsigned long get_sdram_size(void); #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ #define CONFIG_ENV_SECT_SIZE 0x10000 #define CONFIG_ENV_SIZE 0x2000 -#else -#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x2000 -#endif -#else -#define CONFIG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */ +#elif defined(CONFIG_NAND) +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_SYS_EXTRA_ENV_RELOC +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) +#elif defined(CONFIG_SYS_RAMBOOT) +#define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) -#define CONFIG_ENV_SIZE 0x400 +#define CONFIG_ENV_SIZE 0x2000 #endif #define CONFIG_LOADS_ECHO /* echo on for serial download */ @@ -406,7 +442,9 @@ extern unsigned long get_sdram_size(void); "fdtfile=bsc9131rdb.dtb\0" \ "bdev=sda1\0" \ "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" \ - "othbootargs=ramdisk_size=600000 \0" \ + "bootm_size=0x37000000\0" \ + "othbootargs=ramdisk_size=600000 " \ + "default_hugepagesz=256m hugepagesz=256m hugepages=1\0" \ "usbext2boot=setenv bootargs root=/dev/ram rw " \ "console=$consoledev,$baudrate $othbootargs; " \ "usb start;" \ diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h index 9d15d0eb88..3aa44435a2 100644 --- a/include/configs/BSC9132QDS.h +++ b/include/configs/BSC9132QDS.h @@ -49,6 +49,27 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif +#ifdef CONFIG_NAND +#define CONFIG_SPL +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" + +#define CONFIG_SYS_TEXT_BASE 0x00201000 +#define CONFIG_SPL_TEXT_BASE 0xFFFFE000 +#define CONFIG_SPL_MAX_SIZE 8192 +#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 +#define CONFIG_SPL_RELOC_STACK 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" +#endif + #ifndef CONFIG_SYS_TEXT_BASE #define CONFIG_SYS_TEXT_BASE 0x8ff80000 #endif @@ -57,11 +78,12 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0x8ffffffc #endif -#ifndef CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #endif - /* High Level Configuration Options */ #define CONFIG_BOOKE /* BOOKE */ #define CONFIG_E500 /* BOOKE e500 family */ @@ -222,6 +244,10 @@ combinations. this should be removed later * IFC Definitions */ /* NOR Flash on IFC */ + +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_NO_FLASH +#endif #define CONFIG_SYS_FLASH_BASE 0x88000000 #define CONFIG_SYS_MAX_FLASH_SECT 1024 /* Max number of sector: 32M */ @@ -302,7 +328,9 @@ combinations. this should be removed later #define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) +#ifndef CONFIG_SPL_BUILD #define CONFIG_FSL_QIXIS +#endif #ifdef CONFIG_FSL_QIXIS #define CONFIG_SYS_FPGA_BASE 0xffb00000 #define CONFIG_SYS_I2C_FPGA_ADDR 0x66 @@ -338,6 +366,22 @@ combinations. this should be removed later #endif /* Set up IFC registers for boot location NOR/NAND */ +#if defined(CONFIG_NAND) +#define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR +#define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK +#define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR +#define CONFIG_SYS_CS0_FTIM0 CONFIG_SYS_NAND_FTIM0 +#define CONFIG_SYS_CS0_FTIM1 CONFIG_SYS_NAND_FTIM1 +#define CONFIG_SYS_CS0_FTIM2 CONFIG_SYS_NAND_FTIM2 +#define CONFIG_SYS_CS0_FTIM3 CONFIG_SYS_NAND_FTIM3 +#define CONFIG_SYS_CSPR1 CONFIG_SYS_NOR_CSPR +#define CONFIG_SYS_AMASK1 CONFIG_SYS_NOR_AMASK +#define CONFIG_SYS_CSOR1 CONFIG_SYS_NOR_CSOR +#define CONFIG_SYS_CS1_FTIM0 CONFIG_SYS_NOR_FTIM0 +#define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NOR_FTIM1 +#define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NOR_FTIM2 +#define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NOR_FTIM3 +#else #define CONFIG_SYS_CSPR0 CONFIG_SYS_NOR_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NOR_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NOR_CSOR @@ -352,6 +396,7 @@ combinations. this should be removed later #define CONFIG_SYS_CS1_FTIM1 CONFIG_SYS_NAND_FTIM1 #define CONFIG_SYS_CS1_FTIM2 CONFIG_SYS_NAND_FTIM2 #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 +#endif #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ #define CONFIG_BOARD_EARLY_INIT_R @@ -374,6 +419,9 @@ combinations. this should be removed later #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) +#ifdef CONFIG_SPL_BUILD +#define CONFIG_NS16550_MIN_FUNCTIONS +#endif #define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */ #define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine from environment */ @@ -503,7 +551,6 @@ combinations. this should be removed later /* * Environment */ -#if defined(CONFIG_SYS_RAMBOOT) #if defined(CONFIG_RAMBOOT_SDCARD) #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 0 @@ -517,11 +564,15 @@ combinations. this should be removed later #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ #define CONFIG_ENV_SECT_SIZE 0x10000 #define CONFIG_ENV_SIZE 0x2000 -#else +#elif defined(CONFIG_NAND) +#define CONFIG_ENV_IS_IN_NAND +#define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE +#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) +#define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) +#elif defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 -#endif #else #define CONFIG_ENV_IS_IN_FLASH #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h index 5185597905..7b28a27bc0 100644 --- a/include/configs/P1010RDB.h +++ b/include/configs/P1010RDB.h @@ -31,10 +31,10 @@ #define CONFIG_PHYS_64BIT #endif -#ifdef CONFIG_P1010RDB #define CONFIG_P1010 +#define CONFIG_E500 /* BOOKE e500 family */ +#include <asm/config_mpc85xx.h> #define CONFIG_NAND_FSL_IFC -#endif #ifdef CONFIG_SDCARD #define CONFIG_RAMBOOT_SDCARD @@ -48,15 +48,25 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc #endif -#ifdef CONFIG_NAND /* NAND Boot */ -#define CONFIG_RAMBOOT_NAND -#define CONFIG_NAND_U_BOOT -#define CONFIG_SYS_TEXT_BASE_SPL 0xff800000 -#ifdef CONFIG_NAND_SPL -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE_SPL -#else -#define CONFIG_SYS_TEXT_BASE 0x11001000 -#endif /* CONFIG_NAND_SPL */ +#ifdef CONFIG_NAND +#define CONFIG_SPL +#define CONFIG_SPL_INIT_MINIMAL +#define CONFIG_SPL_SERIAL_SUPPORT +#define CONFIG_SPL_NAND_SUPPORT +#define CONFIG_SPL_NAND_MINIMAL +#define CONFIG_SPL_FLUSH_IMAGE +#define CONFIG_SPL_TARGET "u-boot-with-spl.bin" + +#define CONFIG_SYS_TEXT_BASE 0x00201000 +#define CONFIG_SPL_TEXT_BASE 0xFFFFE000 +#define CONFIG_SPL_MAX_SIZE 8192 +#define CONFIG_SPL_RELOC_TEXT_BASE 0x00100000 +#define CONFIG_SPL_RELOC_STACK 0x00100000 +#define CONFIG_SYS_NAND_U_BOOT_SIZE ((512 << 10) - 0x2000) +#define CONFIG_SYS_NAND_U_BOOT_DST (0x00200000 - CONFIG_SPL_MAX_SIZE) +#define CONFIG_SYS_NAND_U_BOOT_START 0x00200000 +#define CONFIG_SYS_NAND_U_BOOT_OFFS 0 +#define CONFIG_SYS_LDSCRIPT "arch/powerpc/cpu/mpc85xx/u-boot-nand.lds" #endif @@ -74,8 +84,10 @@ #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc #endif -#ifndef CONFIG_SYS_MONITOR_BASE -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_MONITOR_BASE CONFIG_SPL_TEXT_BASE +#else +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ #endif /* High Level Configuration Options */ @@ -242,7 +254,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR /* Don't relocate CCSRBAR while in NAND_SPL */ -#ifdef CONFIG_NAND_SPL +#ifdef CONFIG_SPL_BUILD #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE #endif @@ -268,6 +280,10 @@ extern unsigned long get_sdram_size(void); * IFC Definitions */ /* NOR Flash on IFC */ +#ifdef CONFIG_SPL_BUILD +#define CONFIG_SYS_NO_FLASH +#endif + #define CONFIG_SYS_FLASH_BASE 0xee000000 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* 32M */ @@ -353,7 +369,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_NAND_DDR_LAW 11 /* Set up IFC registers for boot location NOR/NAND */ -#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_NAND_SECBOOT) +#if defined(CONFIG_NAND) || defined(CONFIG_NAND_SECBOOT) #define CONFIG_SYS_CSPR0 CONFIG_SYS_NAND_CSPR #define CONFIG_SYS_AMASK0 CONFIG_SYS_NAND_AMASK #define CONFIG_SYS_CSOR0 CONFIG_SYS_NAND_CSOR @@ -385,15 +401,6 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_CS1_FTIM3 CONFIG_SYS_NAND_FTIM3 #endif -/* NAND boot: 8K NAND loader config */ -#define CONFIG_SYS_NAND_SPL_SIZE 0x2000 -#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) -#define CONFIG_SYS_NAND_U_BOOT_DST (0x11000000 - CONFIG_SYS_NAND_SPL_SIZE) -#define CONFIG_SYS_NAND_U_BOOT_START 0x11000000 -#define CONFIG_SYS_NAND_U_BOOT_OFFS (0) -#define CONFIG_SYS_NAND_U_BOOT_RELOC 0x10000 -#define CONFIG_SYS_NAND_U_BOOT_RELOC_SP (CONFIG_SYS_NAND_U_BOOT_RELOC + 0x10000) - /* CPLD on IFC */ #define CONFIG_SYS_CPLD_BASE 0xffb00000 @@ -421,14 +428,20 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_CS3_FTIM3 0x0 #endif /* CONFIG_SDCARD */ -#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) || \ - defined(CONFIG_RAMBOOT_NAND) +#if defined(CONFIG_RAMBOOT_SDCARD) || defined(CONFIG_RAMBOOT_SPIFLASH) #define CONFIG_SYS_RAMBOOT #define CONFIG_SYS_EXTRA_ENV_RELOC #else #undef CONFIG_SYS_RAMBOOT #endif +#ifdef CONFIG_SYS_FSL_ERRATUM_IFC_A003399 +#if !defined(CONFIG_SPL) && !defined(CONFIG_SYS_RAMBOOT)\ + && !defined(CONFIG_SECURE_BOOT) +#define CONFIG_A003399_NOR_WORKAROUND +#endif +#endif + #define CONFIG_BOARD_EARLY_INIT_F /* Call board_pre_init */ #define CONFIG_BOARD_EARLY_INIT_R @@ -450,7 +463,7 @@ extern unsigned long get_sdram_size(void); #define CONFIG_SYS_NS16550_SERIAL #define CONFIG_SYS_NS16550_REG_SIZE 1 #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) -#ifdef CONFIG_NAND_SPL +#ifdef CONFIG_SPL_BUILD #define CONFIG_NS16550_MIN_FUNCTIONS #endif @@ -505,7 +518,7 @@ extern unsigned long get_sdram_size(void); * SPI interface will not be available in case of NAND boot SPI CS0 will be * used for SLIC */ -#if !defined(CONFIG_NAND_U_BOOT) || !defined(CONFIG_NAND_SECBOOT) +#if !defined(CONFIG_NAND) || !defined(CONFIG_NAND_SECBOOT) /* eSPI - Enhanced SPI */ #define CONFIG_FSL_ESPI #define CONFIG_SPI_FLASH @@ -600,7 +613,6 @@ extern unsigned long get_sdram_size(void); /* * Environment */ -#if defined(CONFIG_SYS_RAMBOOT) #if defined(CONFIG_RAMBOOT_SDCARD) #define CONFIG_ENV_IS_IN_MMC #define CONFIG_FSL_FIXED_MMC_LOCATION @@ -615,16 +627,15 @@ extern unsigned long get_sdram_size(void); #define CONFIG_ENV_OFFSET 0x100000 /* 1MB */ #define CONFIG_ENV_SECT_SIZE 0x10000 #define CONFIG_ENV_SIZE 0x2000 -#elif defined(CONFIG_NAND_U_BOOT) +#elif defined(CONFIG_NAND) #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE -#define CONFIG_ENV_OFFSET CONFIG_SYS_NAND_U_BOOT_SIZE +#define CONFIG_ENV_OFFSET ((512 * 1024) + CONFIG_SYS_NAND_BLOCK_SIZE) #define CONFIG_ENV_RANGE (3 * CONFIG_ENV_SIZE) -#else +#elif defined(CONFIG_SYS_RAMBOOT) #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) #define CONFIG_ENV_SIZE 0x2000 -#endif #else #define CONFIG_ENV_IS_IN_FLASH #if CONFIG_SYS_MONITOR_BASE > 0xfff80000 diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h new file mode 100644 index 0000000000..fee8040e2d --- /dev/null +++ b/include/configs/P1023RDB.h @@ -0,0 +1,401 @@ +/* + * Copyright 2013 Freescale Semiconductor, Inc. + * + * Authors: Roy Zang <tie-fei.zang@freescale.com> + * Chunhe Lan <Chunhe.Lan@freescale.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#ifndef CONFIG_SYS_TEXT_BASE +#define CONFIG_SYS_TEXT_BASE 0xeff80000 +#endif + +#ifndef CONFIG_SYS_MONITOR_BASE +#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ +#endif + +#ifndef CONFIG_RESET_VECTOR_ADDRESS +#define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc +#endif + +/* High Level Configuration Options */ +#define CONFIG_BOOKE /* BOOKE */ +#define CONFIG_E500 /* BOOKE e500 family */ +#define CONFIG_MPC85xx +#define CONFIG_P1023 +#define CONFIG_MP /* support multiple processors */ + +#define CONFIG_FSL_ELBC /* Has Enhanced localbus controller */ +#define CONFIG_PCI /* Enable PCI/PCIE */ +#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ +#define CONFIG_PCIE1 /* PCIE controler 1 (slot 1) */ +#define CONFIG_PCIE2 /* PCIE controler 2 (slot 2) */ +#define CONFIG_PCIE3 /* PCIE controler 3 (slot 3) */ +#define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ +#define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ +#define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ +#define CONFIG_FSL_LAW /* Use common FSL init code */ + +#ifndef __ASSEMBLY__ +extern unsigned long get_clock_freq(void); +#endif + +#define CONFIG_SYS_CLK_FREQ 66666666 +#define CONFIG_DDR_CLK_FREQ CONFIG_SYS_CLK_FREQ + +/* + * These can be toggled for performance analysis, otherwise use default. + */ +#define CONFIG_L2_CACHE /* toggle L2 cache */ +#define CONFIG_BTB /* toggle branch predition */ +#define CONFIG_HWCONFIG + +#define CONFIG_ENABLE_36BIT_PHYS + +#define CONFIG_SYS_MEMTEST_START 0x01000000 /* memtest works on */ +#define CONFIG_SYS_MEMTEST_END 0x02000000 + +#define CONFIG_PANIC_HANG /* do not reset board on panic */ + +/* Implement conversion of addresses in the LBC */ +#define CONFIG_SYS_LBC_LBCR 0x00000000 +#define CONFIG_SYS_LBC_LCRR LCRR_CLKDIV_8 + +/* DDR Setup */ +#define CONFIG_VERY_BIG_RAM +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 +#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE + +#define CONFIG_DIMM_SLOTS_PER_CTLR 1 +#define CONFIG_CHIP_SELECTS_PER_CTRL 1 + +#define CONFIG_DDR_SPD +#define CONFIG_FSL_DDR3 +#define CONFIG_FSL_DDR_INTERACTIVE +#define CONFIG_SYS_SDRAM_SIZE 512u /* DDR is 512M */ +#define CONFIG_SYS_SPD_BUS_NUM 0 +#define SPD_EEPROM_ADDRESS 0x50 +#define CONFIG_SYS_DDR_RAW_TIMING + +/* + * Memory map + * + * 0x0000_0000 0x1fff_ffff DDR 512M cacheable + * 0x8000_0000 0xbfff_ffff PCI Express Mem 1G non-cacheable + * 0xc000_0000 0xdfff_ffff PCI 512M non-cacheable + * 0xe100_0000 0xe3ff_ffff PCI IO range 4M non-cacheable + * 0xff00_0000 0xff3f_ffff DPAA_QBMAN 4M cacheable + * 0xff60_0000 0xff7f_ffff CCSR 2M non-cacheable + * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable TLB0 + * + * Localbus non-cacheable + * + * 0xec00_0000 0xefff_ffff NOR flash 64M non-cacheable + * 0xffa0_0000 0xffaf_ffff NAND 1M non-cacheable + */ + +/* + * Local Bus Definitions + */ +#define CONFIG_SYS_FLASH_BASE 0xec000000 /* start of FLASH 64M */ +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE + +#define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ + | BR_PS_16 | BR_V) +#define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 + +#define CONFIG_FLASH_CFI_DRIVER +#define CONFIG_SYS_FLASH_CFI +#define CONFIG_SYS_FLASH_EMPTY_INFO +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ +#define CONFIG_SYS_MAX_FLASH_SECT 512 /* sectors per device */ +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ +#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ + +#define CONFIG_BOARD_EARLY_INIT_F /* call board_early_init_f function */ +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ + +#define CONFIG_SYS_INIT_RAM_LOCK +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* Initial L1 address */ +#define CONFIG_SYS_INIT_RAM_SIZE 0x00004000/* Size of used area in RAM */ +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ + GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET + +#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 kB for Mon */ +#define CONFIG_SYS_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */ + +#define CONFIG_SYS_NAND_BASE 0xffa00000 +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE + +#define CONFIG_SYS_NAND_BASE_LIST { CONFIG_SYS_NAND_BASE } +#define CONFIG_SYS_MAX_NAND_DEVICE 1 +#define CONFIG_MTD_NAND_VERIFY_WRITE +#define CONFIG_CMD_NAND +#define CONFIG_NAND_FSL_ELBC +#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024) + +/* NAND flash config */ +#define CONFIG_SYS_NAND_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \ + | (2<<BR_DECC_SHIFT) /* Use HW ECC */ \ + | BR_PS_8 /* Port Size = 8bit */ \ + | BR_MS_FCM /* MSEL = FCM */ \ + | BR_V) /* valid */ +#define CONFIG_SYS_NAND_OR_PRELIM (OR_AM_256KB /* length 256K */ \ + | OR_FCM_PGS \ + | OR_FCM_CSCT \ + | OR_FCM_CST \ + | OR_FCM_CHT \ + | OR_FCM_SCY_1 \ + | OR_FCM_TRLX \ + | OR_FCM_EHTR) + +#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ +#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ +#define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM +#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ + +/* Serial Port */ +#define CONFIG_CONS_INDEX 1 +#undef CONFIG_SERIAL_SOFTWARE_FIFO +#define CONFIG_SYS_NS16550 +#define CONFIG_SYS_NS16550_SERIAL +#define CONFIG_SYS_NS16550_REG_SIZE 1 +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0) + +#define CONFIG_SYS_BAUDRATE_TABLE \ + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} + +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) + +/* Use the HUSH parser */ +#define CONFIG_SYS_HUSH_PARSER + +/* + * Pass open firmware flat tree + */ +#define CONFIG_OF_LIBFDT +#define CONFIG_OF_BOARD_SETUP +#define CONFIG_OF_STDOUT_VIA_ALIAS + +/* new uImage format support */ +#define CONFIG_FIT +#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */ + +/* I2C */ +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */ +#define CONFIG_HARD_I2C /* I2C with hardware support */ +#define CONFIG_I2C_MULTI_BUS +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CONFIG_SYS_I2C_SLAVE 0x7F +#define CONFIG_SYS_I2C_OFFSET 0x3000 +#define CONFIG_SYS_I2C2_OFFSET 0x3100 + +/* + * I2C2 EEPROM + */ +#define CONFIG_ID_EEPROM +#ifdef CONFIG_ID_EEPROM +#define CONFIG_SYS_I2C_EEPROM_NXID +#endif +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 +#define CONFIG_SYS_EEPROM_BUS_NUM 0 + +#define CONFIG_CMD_I2C + +/* + * General PCI + * Memory space is mapped 1-1, but I/O space must start from 0. + */ + +/* controller 3, Slot 1, tgtid 3, Base address b000 */ +#define CONFIG_SYS_PCIE3_NAME "Slot 3" +#define CONFIG_SYS_PCIE3_MEM_VIRT 0x80000000 +#define CONFIG_SYS_PCIE3_MEM_BUS 0x80000000 +#define CONFIG_SYS_PCIE3_MEM_PHYS 0x80000000 +#define CONFIG_SYS_PCIE3_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE3_IO_VIRT 0xffc00000 +#define CONFIG_SYS_PCIE3_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE3_IO_PHYS 0xffc00000 +#define CONFIG_SYS_PCIE3_IO_SIZE 0x00010000 /* 64k */ + +/* controller 2, direct to uli, tgtid 2, Base address 9000 */ +#define CONFIG_SYS_PCIE2_NAME "Slot 2" +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ + +/* controller 1, Slot 2, tgtid 1, Base address a000 */ +#define CONFIG_SYS_PCIE1_NAME "Slot 1" +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000 +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc20000 +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ + +#if defined(CONFIG_PCI) +#define CONFIG_E1000 /* Defind e1000 pci Ethernet card */ +#define CONFIG_PCI_PNP /* do pci plug-and-play */ +#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ +#endif /* CONFIG_PCI */ + +/* + * Environment + */ +#define CONFIG_ENV_OVERWRITE + +#define CONFIG_ENV_IS_IN_FLASH +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000 +#define CONFIG_ENV_ADDR 0xfff80000 +#else +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) +#endif +#define CONFIG_ENV_SIZE 0x2000 +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ + +#define CONFIG_LOADS_ECHO /* echo on for serial download */ +#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ + +/* + * Command line configuration. + */ +#include <config_cmd_default.h> + +#define CONFIG_CMD_IRQ +#define CONFIG_CMD_PING +#define CONFIG_CMD_MII +#define CONFIG_CMD_SETEXPR +#define CONFIG_CMD_REGINFO + +#if defined(CONFIG_PCI) +#define CONFIG_CMD_PCI +#define CONFIG_CMD_NET +#endif + +/* + * USB + */ +#define CONFIG_HAS_FSL_DR_USB +#ifdef CONFIG_HAS_FSL_DR_USB +#define CONFIG_USB_EHCI + +#ifdef CONFIG_USB_EHCI +#define CONFIG_CMD_USB +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET +#define CONFIG_USB_EHCI_FSL +#define CONFIG_USB_STORAGE +#define CONFIG_CMD_FAT +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION +#endif +#endif + +/* + * Miscellaneous configurable options + */ +#define CONFIG_SYS_LONGHELP /* undef to save memory */ +#define CONFIG_CMDLINE_EDITING /* Command-line editing */ +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ +#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ +#if defined(CONFIG_CMD_KGDB) +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ +#else +#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ +#endif +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16) +#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ +/* Boot Argument Buffer Size */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */ + +/* + * For booting Linux, the board info and command line data + * have to be in the first 64 MB of memory, since this is + * the maximum mapped by the Linux kernel during initialization. + */ +#define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory map for Linux*/ +#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ + +/* + * Environment Configuration + */ +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_UBOOTPATH (u-boot.bin) /* U-Boot image on TFTP server */ + +/* default location for tftp and bootm */ +#define CONFIG_LOADADDR 1000000 + +#define CONFIG_BOOTDELAY -1 /* -1 disables auto-boot */ + +#define CONFIG_BAUDRATE 115200 + +/* Qman/Bman */ +#define CONFIG_SYS_DPAA_QBMAN /* support Q/Bman */ +#define CONFIG_SYS_QMAN_MEM_BASE 0xff000000 +#define CONFIG_SYS_QMAN_MEM_PHYS CONFIG_SYS_QMAN_MEM_BASE +#define CONFIG_SYS_QMAN_MEM_SIZE 0x00200000 +#define CONFIG_SYS_BMAN_MEM_BASE 0xff200000 +#define CONFIG_SYS_BMAN_MEM_PHYS CONFIG_SYS_BMAN_MEM_BASE +#define CONFIG_SYS_BMAN_MEM_SIZE 0x00200000 + +/* For FM */ +#define CONFIG_SYS_DPAA_FMAN +#define CONFIG_PHY_GIGE /* Include GbE speed/duplex detection */ + +#ifdef CONFIG_SYS_DPAA_FMAN +#define CONFIG_FMAN_ENET +#define CONFIG_PHY_ATHEROS +#endif + +/* Default address of microcode for the Linux Fman driver */ +/* QE microcode/firmware address */ +#define CONFIG_SYS_QE_FMAN_FW_IN_NOR +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xeff40000 +#define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 +#define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) + +#ifdef CONFIG_FMAN_ENET +#define CONFIG_SYS_FM1_DTSEC1_PHY_ADDR 0x1 +#define CONFIG_SYS_FM1_DTSEC2_PHY_ADDR 0x2 + +#define CONFIG_SYS_TBIPA_VALUE 8 +#define CONFIG_MII /* MII PHY management */ +#define CONFIG_ETHPRIME "FM1@DTSEC1" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0" + +#endif /* __CONFIG_H */ diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h index 9cd3a7cb34..4ea8717368 100644 --- a/include/configs/P2041RDB.h +++ b/include/configs/P2041RDB.h @@ -77,6 +77,7 @@ #define CONFIG_SYS_SRIO #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ +#define CONFIG_SRIO_PCIE_BOOT_MASTER #define CONFIG_SYS_DPAA_RMAN /* RMan */ #define CONFIG_FSL_LAW /* Use common FSL init code */ diff --git a/include/configs/P3041DS.h b/include/configs/P3041DS.h index ce8f9b0b2e..dd2b9c34e4 100644 --- a/include/configs/P3041DS.h +++ b/include/configs/P3041DS.h @@ -40,7 +40,7 @@ #define CONFIG_SYS_SRIO #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ - +#define CONFIG_SRIO_PCIE_BOOT_MASTER #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ #include "corenet_ds.h" diff --git a/include/configs/P4080DS.h b/include/configs/P4080DS.h index 53979dddf2..48acee4993 100644 --- a/include/configs/P4080DS.h +++ b/include/configs/P4080DS.h @@ -36,7 +36,7 @@ #define CONFIG_SYS_SRIO #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ - +#define CONFIG_SRIO_PCIE_BOOT_MASTER #define CONFIG_ICS307_REFCLK_HZ 33333000 /* ICS307 ref clk freq */ #include "corenet_ds.h" diff --git a/include/configs/P5020DS.h b/include/configs/P5020DS.h index 778230d335..d1e27c42d4 100644 --- a/include/configs/P5020DS.h +++ b/include/configs/P5020DS.h @@ -41,7 +41,7 @@ #define CONFIG_SYS_SRIO #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ - +#define CONFIG_SRIO_PCIE_BOOT_MASTER #define CONFIG_ICS307_REFCLK_HZ 25000000 /* ICS307 ref clk freq */ #include "corenet_ds.h" diff --git a/include/configs/a3m071.h b/include/configs/a3m071.h index e9af825663..8f29229cdc 100644 --- a/include/configs/a3m071.h +++ b/include/configs/a3m071.h @@ -426,6 +426,7 @@ #define CONFIG_SPL_BSS_MAX_SIZE (64 << 10) #define CONFIG_SPL_OS_BOOT +#define CONFIG_SPL_ENV_SUPPORT /* Place patched DT blob (fdt) at this address */ #define CONFIG_SYS_SPL_ARGS_ADDR 0x01800000 diff --git a/include/configs/ac14xx.h b/include/configs/ac14xx.h index 7cb10fb01e..381bcdda0d 100644 --- a/include/configs/ac14xx.h +++ b/include/configs/ac14xx.h @@ -72,7 +72,7 @@ #define CONFIG_SYS_MAX_RAM_SIZE 0x20000000 /* - * DDR Controller Configuration XXX TODO + * DDR Controller Configuration * * SYS_CFG: * [31:31] MDDRC Soft Reset: Diabled @@ -265,7 +265,6 @@ /* * CS related parameters - * TODO document these */ /* CS0 Flash */ #define CONFIG_SYS_CS0_CFG 0x00031110 @@ -331,8 +330,6 @@ #endif #define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */ -#define CONFIG_SYS_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200} #define CONSOLE_FIFO_TX_SIZE FIFOC_PSC3_TX_SIZE #define CONSOLE_FIFO_TX_ADDR FIFOC_PSC3_TX_ADDR @@ -497,30 +494,26 @@ #define CONFIG_ENV_OVERWRITE #define CONFIG_TIMESTAMP -#define CONFIG_HOSTNAME ac14xx -#define CONFIG_BOOTFILE "ac14xx/uImage" -#define CONFIG_ROOTPATH "/opt/eldk/ppc_6xx" - /* default load addr for tftp and bootm */ #define CONFIG_LOADADDR 400000 #define CONFIG_BOOTDELAY 2 /* -1 disables auto-boot */ -/* XXX TODO need to specify the builtin environment */ +/* the builtin environment and standard greeting */ #define CONFIG_PREBOOT "echo;" \ "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ "echo" #define CONFIG_EXTRA_ENV_SETTINGS_DEVEL \ - "muster_nr=00\0" \ + "muster_nr=-00\0" \ "fromram=run ramargs addip addtty; " \ - "tftp ${fdt_addr_r} k6m2/ac14xx.dtb-${muster_nr}; " \ - "tftp ${kernel_addr_r} k6m2/uImage-${muster_nr}; " \ - "tftp ${ramdisk_addr_r} k6m2/uFS-${muster_nr}; " \ + "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; " \ + "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; " \ + "tftp ${ramdisk_addr_r} ac14xx/uFS${muster_nr}; " \ "bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}\0" \ "fromnfs=run nfsargs addip addtty; " \ - "tftp ${fdt_addr_r} k6m2/ac14xx.dtb-${muster_nr}; " \ - "tftp ${kernel_addr_r} k6m2/uImage-${muster_nr}; " \ + "tftp ${fdt_addr_r} ac14xx/ac14xx.dtb${muster_nr}; " \ + "tftp ${kernel_addr_r} ac14xx/uImage${muster_nr}; " \ "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ "fromflash=run nfsargs addip addtty; " \ "bootm fc020000 - fc000000\0" \ @@ -548,12 +541,11 @@ "u-boot=ac14xx/u-boot.bin\0" \ "bootfile=ac14xx/uImage\0" \ "fdtfile=ac14xx/ac14xx.dtb\0" \ - "rootpath=/opt/eldk/ppc_6xx\n" \ "netdev=eth0\0" \ "consdev=ttyPSC0\0" \ "hostname=ac14xx\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}-${muster_nr}\0" \ + "nfsroot=${serverip}:${rootpath}${muster_nr}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ "addip=setenv bootargs ${bootargs} " \ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ @@ -583,6 +575,8 @@ #define CONFIG_BOOTCOMMAND "run production" +#define CONFIG_ARP_TIMEOUT 200UL + #define CONFIG_FIT 1 #define CONFIG_OF_LIBFDT 1 #define CONFIG_OF_BOARD_SETUP 1 diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h index 737e19ee6f..c5a6d4b315 100644 --- a/include/configs/am335x_evm.h +++ b/include/configs/am335x_evm.h @@ -60,7 +60,7 @@ "rdaddr=0x81000000\0" \ "bootdir=/boot\0" \ "bootfile=uImage\0" \ - "fdtfile=\0" \ + "fdtfile=undefined\0" \ "console=ttyO0,115200n8\0" \ "optargs=\0" \ "mtdids=" MTDIDS_DEFAULT "\0" \ @@ -145,8 +145,9 @@ "if test $board_name = A33515BB; then " \ "setenv fdtfile am335x-evm.dtb; fi; " \ "if test $board_name = A335X_SK; then " \ - "setenv fdtfile am335x-evmsk.dtb; fi\0" \ - + "setenv fdtfile am335x-evmsk.dtb; fi; " \ + "if test $fdtfile = undefined; then " \ + "echo WARNING: Could not determine device tree to use; fi; \0" #endif #define CONFIG_BOOTCOMMAND \ @@ -355,6 +356,7 @@ #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_YMODEM_SUPPORT #define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT #define CONFIG_SPL_NET_VCI_STRING "AM335x U-Boot SPL" #define CONFIG_SPL_ETH_SUPPORT #define CONFIG_SPL_SPI_SUPPORT diff --git a/include/configs/at91sam9n12ek.h b/include/configs/at91sam9n12ek.h index 8d2673dacb..b4b1c31960 100644 --- a/include/configs/at91sam9n12ek.h +++ b/include/configs/at91sam9n12ek.h @@ -167,6 +167,10 @@ #define CONFIG_DOS_PARTITION #endif +/* Ethernet */ +#define CONFIG_KS8851_MLL +#define CONFIG_KS8851_MLL_BASEADDR 0x30000000 /* use NCS2 */ + #define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */ #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE diff --git a/include/configs/coreboot.h b/include/configs/coreboot.h index 2fefdc80db..288ef8df74 100644 --- a/include/configs/coreboot.h +++ b/include/configs/coreboot.h @@ -168,6 +168,13 @@ */ #include <config_cmd_default.h> +#define CONFIG_TRACE +#define CONFIG_CMD_TRACE +#define CONFIG_TRACE_BUFFER_SIZE (16 << 20) +#define CONFIG_TRACE_EARLY_SIZE (8 << 20) +#define CONFIG_TRACE_EARLY +#define CONFIG_TRACE_EARLY_ADDR 0x01400000 + #define CONFIG_CMD_BDI #define CONFIG_CMD_BOOTD #define CONFIG_CMD_CONSOLE diff --git a/include/configs/dra7xx_evm.h b/include/configs/dra7xx_evm.h index 0eea28c80a..c11f005535 100644 --- a/include/configs/dra7xx_evm.h +++ b/include/configs/dra7xx_evm.h @@ -41,4 +41,7 @@ #define CONFIG_BAUDRATE 115200 #define CONFIG_SYS_OMAP_ABE_SYSCK + +#define CONSOLEDEV "ttyO0" + #endif /* __CONFIG_DRA7XX_EVM_H */ diff --git a/include/configs/exynos5250-dt.h b/include/configs/exynos5250-dt.h index 41d6cf9d15..e2a096b643 100644 --- a/include/configs/exynos5250-dt.h +++ b/include/configs/exynos5250-dt.h @@ -43,6 +43,14 @@ #define CONFIG_OF_CONTROL #define CONFIG_OF_SEPARATE +/* Allow tracing to be enabled */ +#define CONFIG_TRACE +#define CONFIG_CMD_TRACE +#define CONFIG_TRACE_BUFFER_SIZE (16 << 20) +#define CONFIG_TRACE_EARLY_SIZE (8 << 20) +#define CONFIG_TRACE_EARLY +#define CONFIG_TRACE_EARLY_ADDR 0x50000000 + /* Keep L2 Cache Disabled */ #define CONFIG_SYS_DCACHE_OFF @@ -82,24 +90,34 @@ #define CONFIG_BAUDRATE 115200 #define EXYNOS5_DEFAULT_UART_OFFSET 0x010000 +/* Enable keyboard */ +#define CONFIG_CROS_EC /* CROS_EC protocol */ +#define CONFIG_CROS_EC_SPI /* Support CROS_EC over SPI */ +#define CONFIG_CROS_EC_I2C /* Support CROS_EC over I2C */ +#define CONFIG_CROS_EC_KEYB /* CROS_EC keyboard input */ +#define CONFIG_CMD_CROS_EC +#define CONFIG_KEYBOARD + /* Console configuration */ #define CONFIG_CONSOLE_MUX #define CONFIG_SYS_CONSOLE_IS_IN_ENV #define EXYNOS_DEVICE_SETTINGS \ - "stdin=serial\0" \ + "stdin=serial,cros-ec-keyb\0" \ "stdout=serial,lcd\0" \ "stderr=serial,lcd\0" #define CONFIG_EXTRA_ENV_SETTINGS \ EXYNOS_DEVICE_SETTINGS -#define TZPC_BASE_OFFSET 0x10000 - /* SD/MMC configuration */ #define CONFIG_GENERIC_MMC #define CONFIG_MMC #define CONFIG_SDHCI #define CONFIG_S5P_SDHCI +#define CONFIG_DWMMC +#define CONFIG_EXYNOS_DWMMC +#define CONFIG_SUPPORT_EMMC_BOOT + #define CONFIG_BOARD_EARLY_INIT_F @@ -232,6 +250,10 @@ #define SPI_FLASH_UBOOT_POS (CONFIG_SEC_FW_SIZE + CONFIG_BL1_SIZE) #define CONFIG_DOS_PARTITION +#define CONFIG_EFI_PARTITION +#define CONFIG_CMD_PART +#define CONFIG_PARTITION_UUIDS + #define CONFIG_IRAM_STACK 0x02050000 @@ -262,6 +284,7 @@ #define CONFIG_CMD_SF #define CONFIG_CMD_SPI #define CONFIG_SPI_FLASH_WINBOND +#define CONFIG_SPI_FLASH_GIGADEVICE #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 #define CONFIG_SF_DEFAULT_SPEED 50000000 #define EXYNOS5_SPI_NUM_CONTROLLERS 5 diff --git a/include/configs/lacie_kw.h b/include/configs/lacie_kw.h index 09b5798d57..e2b3b21182 100644 --- a/include/configs/lacie_kw.h +++ b/include/configs/lacie_kw.h @@ -120,10 +120,14 @@ #endif /* + * Enable platform initialisation via misc_init_r() function + */ +#define CONFIG_MISC_INIT_R + +/* * Ethernet Driver configuration */ #ifdef CONFIG_CMD_NET -#define CONFIG_MISC_INIT_R /* Call misc_init_r() to initialize MAC address */ #define CONFIG_MVGBE_PORTS {1, 0} /* enable port 0 only */ #define CONFIG_NETCONSOLE #endif @@ -153,6 +157,9 @@ #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* 16-byte page size */ #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* 8-bit device address */ +#if defined(CONFIG_NET2BIG_V2) +#define CONFIG_SYS_I2C_G762_ADDR 0x3e +#endif #endif /* CONFIG_CMD_I2C */ /* diff --git a/include/configs/omap4_common.h b/include/configs/omap4_common.h index 3e5d36b21e..2fa4382c3e 100644 --- a/include/configs/omap4_common.h +++ b/include/configs/omap4_common.h @@ -150,6 +150,7 @@ "console=ttyO2,115200n8\0" \ "fdt_high=0xffffffff\0" \ "fdtaddr=0x80f80000\0" \ + "fdtfile=undefined\0" \ "bootpart=0:2\0" \ "bootdir=/boot\0" \ "bootfile=zImage\0" \ @@ -177,8 +178,12 @@ "setenv fdtfile omap4-sdp.dtb; fi; " \ "if test $board_name = panda; then " \ "setenv fdtfile omap4-panda.dtb; fi;" \ + "if test $board_name = panda-a4; then " \ + "setenv fdtfile omap4-panda-a4.dtb; fi;" \ "if test $board_name = panda-es; then " \ - "setenv fdtfile omap4-panda-es.dtb; fi; \0" \ + "setenv fdtfile omap4-panda-es.dtb; fi;" \ + "if test $fdtfile = undefined; then " \ + "echo WARNING: Could not determine device tree to use; fi; \0" \ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \ #define CONFIG_BOOTCOMMAND \ diff --git a/include/configs/omap5_common.h b/include/configs/omap5_common.h index ddf2ad4fc2..b87ee42286 100644 --- a/include/configs/omap5_common.h +++ b/include/configs/omap5_common.h @@ -136,9 +136,10 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "loadaddr=0x82000000\0" \ - "console=ttyO2,115200n8\0" \ + "console=" CONSOLEDEV ",115200n8\0" \ "fdt_high=0xffffffff\0" \ "fdtaddr=0x80f80000\0" \ + "fdtfile=undefined\0" \ "bootpart=0:2\0" \ "bootdir=/boot\0" \ "bootfile=zImage\0" \ @@ -166,7 +167,11 @@ "bootz ${loadaddr} - ${fdtaddr}\0" \ "findfdt="\ "if test $board_name = omap5_uevm; then " \ - "setenv fdtfile omap5-uevm.dtb; fi;\0 " \ + "setenv fdtfile omap5-uevm.dtb; fi; " \ + "if test $board_name = dra7xx; then " \ + "setenv fdtfile dra7-evm.dtb; fi;" \ + "if test $fdtfile = undefined; then " \ + "echo WARNING: Could not determine device tree to use; fi; \0" \ "loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile};\0" \ #define CONFIG_BOOTCOMMAND \ diff --git a/include/configs/omap5_uevm.h b/include/configs/omap5_uevm.h index dea05bc911..46dacc2074 100644 --- a/include/configs/omap5_uevm.h +++ b/include/configs/omap5_uevm.h @@ -53,7 +53,9 @@ #define CONFIG_PARTITION_UUIDS #define CONFIG_CMD_PART -#define CONFIG_SYS_PROMPT "OMAP5430 EVM # " +#define CONFIG_SYS_PROMPT "OMAP5432 uEVM # " + +#define CONSOLEDEV "ttyO2" #define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296 #endif /* __CONFIG_OMAP5_EVM_H */ diff --git a/include/configs/origen.h b/include/configs/origen.h index ff2b24d97f..e179911d0c 100644 --- a/include/configs/origen.h +++ b/include/configs/origen.h @@ -96,6 +96,8 @@ #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x02020030 +#define CONFIG_SPL_TEXT_BASE 0x02021410 + #define CONFIG_BOOTCOMMAND "fatload mmc 0 40007000 uImage; bootm 40007000" /* Miscellaneous configurable options */ diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h index 2ecd1050cf..9b16c47820 100644 --- a/include/configs/pcm051.h +++ b/include/configs/pcm051.h @@ -231,6 +231,7 @@ #define CONFIG_SPL_GPIO_SUPPORT #define CONFIG_SPL_YMODEM_SUPPORT #define CONFIG_SPL_NET_SUPPORT +#define CONFIG_SPL_ENV_SUPPORT #define CONFIG_SPL_NET_VCI_STRING "pcm051 U-Boot SPL" #define CONFIG_SPL_ETH_SUPPORT #define CONFIG_SPL_SPI_SUPPORT diff --git a/include/configs/sandbox.h b/include/configs/sandbox.h index 788207d007..98dd083302 100644 --- a/include/configs/sandbox.h +++ b/include/configs/sandbox.h @@ -22,6 +22,19 @@ #ifndef __CONFIG_H #define __CONFIG_H +#ifdef FTRACE +#define CONFIG_TRACE +#define CONFIG_CMD_TRACE +#define CONFIG_TRACE_BUFFER_SIZE (16 << 20) +#define CONFIG_TRACE_EARLY_SIZE (8 << 20) +#define CONFIG_TRACE_EARLY +#define CONFIG_TRACE_EARLY_ADDR 0x00100000 + +#endif + +#define CONFIG_BOOTSTAGE +#define CONFIG_BOOTSTAGE_REPORT + /* Number of bits in a C 'long' on this architecture */ #define CONFIG_SANDBOX_BITS_PER_LONG 64 @@ -30,6 +43,8 @@ #define CONFIG_OF_LIBFDT #define CONFIG_LMB #define CONFIG_FIT +#define CONFIG_FIT_SIGNATURE +#define CONFIG_RSA #define CONFIG_CMD_FDT #define CONFIG_FS_FAT diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h index b796b46a7f..5e430660f1 100644 --- a/include/configs/smdkv310.h +++ b/include/configs/smdkv310.h @@ -95,6 +95,8 @@ #define CONFIG_SPL #define COPY_BL2_FNPTR_ADDR 0x00002488 +#define CONFIG_SPL_TEXT_BASE 0x02021410 + #define CONFIG_BOOTCOMMAND "fatload mmc 0 40007000 uImage; bootm 40007000" /* Miscellaneous configurable options */ diff --git a/include/configs/t4qds.h b/include/configs/t4qds.h index aa90249f0f..92b2179ca7 100644 --- a/include/configs/t4qds.h +++ b/include/configs/t4qds.h @@ -33,6 +33,15 @@ #define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t4qds/t4_rcw.cfg #endif +#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE +/* Set 1M boot space */ +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000) +#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \ + (0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR) +#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc +#define CONFIG_SYS_NO_FLASH +#endif + #define CONFIG_CMD_REGINFO /* High Level Configuration Options */ @@ -65,20 +74,22 @@ #define CONFIG_SYS_SRIO #define CONFIG_SRIO1 /* SRIO port 1 */ #define CONFIG_SRIO2 /* SRIO port 2 */ +#define CONFIG_SRIO_PCIE_BOOT_MASTER #define CONFIG_FSL_LAW /* Use common FSL init code */ #define CONFIG_ENV_OVERWRITE #ifdef CONFIG_SYS_NO_FLASH +#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL) #define CONFIG_ENV_IS_NOWHERE +#endif #else #define CONFIG_FLASH_CFI_DRIVER #define CONFIG_SYS_FLASH_CFI #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE #endif -#ifndef CONFIG_SYS_NO_FLASH #if defined(CONFIG_SPIFLASH) #define CONFIG_SYS_EXTRA_ENV_RELOC #define CONFIG_ENV_IS_IN_SPI_FLASH @@ -100,18 +111,18 @@ #define CONFIG_ENV_IS_IN_NAND #define CONFIG_ENV_SIZE CONFIG_SYS_NAND_BLOCK_SIZE #define CONFIG_ENV_OFFSET (5 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +#define CONFIG_ENV_IS_IN_REMOTE +#define CONFIG_ENV_ADDR 0xffe20000 +#define CONFIG_ENV_SIZE 0x2000 +#elif defined(CONFIG_ENV_IS_NOWHERE) +#define CONFIG_ENV_SIZE 0x2000 #else #define CONFIG_ENV_IS_IN_FLASH #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE) #define CONFIG_ENV_SIZE 0x2000 #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ #endif -#else /* CONFIG_SYS_NO_FLASH */ -#define CONFIG_ENV_SIZE 0x2000 -#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ -#endif - - #define CONFIG_SYS_CLK_FREQ get_board_sys_clk() #define CONFIG_DDR_CLK_FREQ get_board_ddr_clk() @@ -633,6 +644,16 @@ unsigned long get_board_ddr_clk(void); #elif defined(CONFIG_NAND) #define CONFIG_SYS_QE_FMAN_FW_IN_NAND #define CONFIG_SYS_QE_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) +#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) +/* + * Slave has no ucode locally, it can fetch this from remote. When implementing + * in two corenet boards, slave's ucode could be stored in master's memory + * space, the address can be mapped from slave TLB->slave LAW-> + * slave SRIO or PCIE outbound window->master inbound window-> + * master LAW->the ucode address in master's memory space. + */ +#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE +#define CONFIG_SYS_QE_FMAN_FW_ADDR 0xFFE00000 #else #define CONFIG_SYS_QE_FMAN_FW_IN_NOR #define CONFIG_SYS_QE_FMAN_FW_ADDR 0xEFF40000 diff --git a/include/configs/trats.h b/include/configs/trats.h index fd58558beb..c70838b915 100644 --- a/include/configs/trats.h +++ b/include/configs/trats.h @@ -146,7 +146,8 @@ #define CONFIG_DFU_ALT \ "u-boot mmc 80 400;" \ - "uImage ext4 0 2\0" \ + "uImage ext4 0 2;" \ + "exynos4210-trats.dtb ext4 0 2\0" #define CONFIG_ENV_OVERWRITE #define CONFIG_SYS_CONSOLE_INFO_QUIET @@ -154,7 +155,7 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "bootk=" \ - "run loaduimage; bootm 0x40007FC0\0" \ + "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ "updatemmc=" \ "mmc boot 0 1 1 1; mmc write 0 0x42008000 0 0x200;" \ "mmc boot 0 1 1 0\0" \ @@ -177,7 +178,7 @@ "mmcboot=" \ "setenv bootargs root=/dev/mmcblk${mmcdev}p${mmcrootpart} " \ "${lpj} rootwait ${console} ${meminfo} ${opts} ${lcdinfo}; " \ - "run loaduimage; bootm 0x40007FC0\0" \ + "run loaddtb; run loaduimage; bootm 0x40007FC0 - ${fdtaddr}\0" \ "bootchart=setenv opts init=/sbin/bootchartd; run bootcmd\0" \ "boottrace=setenv opts initcall_debug; run bootcmd\0" \ "mmcoops=mmc read 0 0x40000000 0x40 8; md 0x40000000 0x400\0" \ @@ -188,6 +189,8 @@ "nfsroot=/nfsroot/arm\0" \ "bootblock=" CONFIG_BOOTBLOCK "\0" \ "loaduimage=ext4load mmc ${mmcdev}:${mmcbootpart} 0x40007FC0 uImage\0" \ + "loaddtb=ext4load mmc ${mmcdev}:${mmcbootpart} ${fdtaddr}" \ + "${fdtfile}\0" \ "mmcdev=0\0" \ "mmcbootpart=2\0" \ "mmcrootpart=5\0" \ @@ -212,7 +215,10 @@ " /${splfile} ${spl_imgaddr} ${spl_imgsize};" \ "setenv spl_imgsize;" \ "setenv spl_imgaddr;" \ - "setenv spl_addr_tmp;\0" + "setenv spl_addr_tmp;\0" \ + "fdtaddr=40800000\0" \ + "fdtfile=exynos4210-trats.dtb\0" + /* Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP /* undef to save memory */ @@ -322,4 +328,7 @@ #define CONFIG_USB_GADGET_MASS_STORAGE #endif +/* Pass open firmware flat tree */ +#define CONFIG_OF_LIBFDT 1 + #endif /* __CONFIG_H */ |