aboutsummaryrefslogtreecommitdiff
path: root/drivers/usb/host
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/usb/host')
-rw-r--r--drivers/usb/host/Kconfig48
-rw-r--r--drivers/usb/host/dwc2.c52
-rw-r--r--drivers/usb/host/dwc2.h42
-rw-r--r--drivers/usb/host/ehci-omap.c13
4 files changed, 91 insertions, 64 deletions
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
index 427b360af1..10b0479a8a 100644
--- a/drivers/usb/host/Kconfig
+++ b/drivers/usb/host/Kconfig
@@ -57,6 +57,16 @@ config USB_XHCI_OCTEON
family SoCs. This is a driver for the dwc3 to provide the glue logic
to configure the controller.
+config USB_XHCI_OMAP
+ bool "Support for TI OMAP family xHCI USB controller"
+ depends on ARCH_OMAP2PLUS
+ help
+ Enables support for the on-chip xHCI controller found on some TI SoC
+ families. Note that some families have multiple contollers while
+ others only have something such as DesignWare-based controllers.
+ Consult the SoC documentation to determine if this option applies
+ to your hardware.
+
config USB_XHCI_PCI
bool "Support for PCI-based xHCI USB controller"
depends on DM_USB
@@ -146,7 +156,6 @@ config USB_EHCI_MARVELL
config USB_EHCI_MX5
bool "Support for i.MX5 on-chip EHCI USB controller"
depends on ARCH_MX5
- default n
help
Enables support for the on-chip EHCI controller on i.MX5 SoCs.
@@ -174,6 +183,40 @@ config USB_EHCI_OMAP
Enables support for the on-chip EHCI controller on OMAP3 and later
SoCs.
+if USB_EHCI_OMAP
+
+config HAS_OMAP_EHCI_PHY1_RESET_GPIO
+ bool "PHY #1 requires a GPIO hold to it in RESET while PHY settles"
+ help
+ Enable this to be able to configure the GPIO number used to hold the
+ PHY in RESET for enough time until the PHY is settled and ready.
+
+config OMAP_EHCI_PHY1_RESET_GPIO
+ int "GPIO number to hold PHY #1 in RESET"
+ depends on HAS_OMAP_EHCI_PHY1_RESET_GPIO
+
+config HAS_OMAP_EHCI_PHY2_RESET_GPIO
+ bool "PHY #2 requires a GPIO hold to it in RESET while PHY settles"
+ help
+ Enable this to be able to configure the GPIO number used to hold the
+ PHY in RESET for enough time until the PHY is settled and ready.
+
+config OMAP_EHCI_PHY2_RESET_GPIO
+ int "GPIO number to hold PHY #2 in RESET"
+ depends on HAS_OMAP_EHCI_PHY2_RESET_GPIO
+
+config HAS_OMAP_EHCI_PHY3_RESET_GPIO
+ bool "PHY #3 requires a GPIO hold to it in RESET while PHY settles"
+ help
+ Enable this to be able to configure the GPIO number used to hold the
+ PHY in RESET for enough time until the PHY is settled and ready.
+
+config OMAP_EHCI_PHY3_RESET_GPIO
+ int "GPIO number to hold PHY #3 in RESET"
+ depends on HAS_OMAP_EHCI_PHY3_RESET_GPIO
+
+endif
+
config USB_EHCI_VF
bool "Support for Vybrid on-chip EHCI USB controller"
depends on ARCH_VF610
@@ -195,7 +238,6 @@ config USB_EHCI_MSM
depends on DM_USB
select USB_ULPI_VIEWPORT
select MSM8916_USB_PHY
- default n
---help---
Enables support for the on-chip EHCI controller on Qualcomm
Snapdragon SoCs.
@@ -222,13 +264,11 @@ config USB_EHCI_GENERIC
bool "Support for generic EHCI USB controller"
depends on DM_USB
default ARCH_SUNXI
- default n
---help---
Enables support for generic EHCI controller.
config USB_EHCI_FSL
bool "Support for FSL on-chip EHCI USB controller"
- default n
select CONFIG_EHCI_HCD_INIT_AFTER_RESET
---help---
Enables support for the on-chip EHCI controller on FSL chips.
diff --git a/drivers/usb/host/dwc2.c b/drivers/usb/host/dwc2.c
index 43cc2e0433..23060fc369 100644
--- a/drivers/usb/host/dwc2.c
+++ b/drivers/usb/host/dwc2.c
@@ -86,14 +86,14 @@ static void init_fslspclksel(struct dwc2_core_regs *regs)
{
uint32_t phyclk;
-#if (CONFIG_DWC2_PHY_TYPE == DWC2_PHY_TYPE_FS)
+#if (DWC2_PHY_TYPE == DWC2_PHY_TYPE_FS)
phyclk = DWC2_HCFG_FSLSPCLKSEL_48_MHZ; /* Full speed PHY */
#else
/* High speed PHY running at full speed or high speed */
phyclk = DWC2_HCFG_FSLSPCLKSEL_30_60_MHZ;
#endif
-#ifdef CONFIG_DWC2_ULPI_FS_LS
+#ifdef DWC2_ULPI_FS_LS
uint32_t hwcfg2 = readl(&regs->ghwcfg2);
uint32_t hval = (ghwcfg2 & DWC2_HWCFG2_HS_PHY_TYPE_MASK) >>
DWC2_HWCFG2_HS_PHY_TYPE_OFFSET;
@@ -257,28 +257,28 @@ static void dwc_otg_core_host_init(struct udevice *dev,
/* Initialize Host Configuration Register */
init_fslspclksel(regs);
-#ifdef CONFIG_DWC2_DFLT_SPEED_FULL
+#ifdef DWC2_DFLT_SPEED_FULL
setbits_le32(&regs->host_regs.hcfg, DWC2_HCFG_FSLSSUPP);
#endif
/* Configure data FIFO sizes */
-#ifdef CONFIG_DWC2_ENABLE_DYNAMIC_FIFO
+#ifdef DWC2_ENABLE_DYNAMIC_FIFO
if (readl(&regs->ghwcfg2) & DWC2_HWCFG2_DYNAMIC_FIFO) {
/* Rx FIFO */
- writel(CONFIG_DWC2_HOST_RX_FIFO_SIZE, &regs->grxfsiz);
+ writel(DWC2_HOST_RX_FIFO_SIZE, &regs->grxfsiz);
/* Non-periodic Tx FIFO */
- nptxfifosize |= CONFIG_DWC2_HOST_NPERIO_TX_FIFO_SIZE <<
+ nptxfifosize |= DWC2_HOST_NPERIO_TX_FIFO_SIZE <<
DWC2_FIFOSIZE_DEPTH_OFFSET;
- nptxfifosize |= CONFIG_DWC2_HOST_RX_FIFO_SIZE <<
+ nptxfifosize |= DWC2_HOST_RX_FIFO_SIZE <<
DWC2_FIFOSIZE_STARTADDR_OFFSET;
writel(nptxfifosize, &regs->gnptxfsiz);
/* Periodic Tx FIFO */
- ptxfifosize |= CONFIG_DWC2_HOST_PERIO_TX_FIFO_SIZE <<
+ ptxfifosize |= DWC2_HOST_PERIO_TX_FIFO_SIZE <<
DWC2_FIFOSIZE_DEPTH_OFFSET;
- ptxfifosize |= (CONFIG_DWC2_HOST_RX_FIFO_SIZE +
- CONFIG_DWC2_HOST_NPERIO_TX_FIFO_SIZE) <<
+ ptxfifosize |= (DWC2_HOST_RX_FIFO_SIZE +
+ DWC2_HOST_NPERIO_TX_FIFO_SIZE) <<
DWC2_FIFOSIZE_STARTADDR_OFFSET;
writel(ptxfifosize, &regs->hptxfsiz);
}
@@ -340,7 +340,7 @@ static void dwc_otg_core_init(struct udevice *dev)
struct dwc2_core_regs *regs = priv->regs;
uint32_t ahbcfg = 0;
uint32_t usbcfg = 0;
- uint8_t brst_sz = CONFIG_DWC2_DMA_BURST_SIZE;
+ uint8_t brst_sz = DWC2_DMA_BURST_SIZE;
/* Common Initialization */
usbcfg = readl(&regs->gusbcfg);
@@ -357,7 +357,7 @@ static void dwc_otg_core_init(struct udevice *dev)
}
/* Set external TS Dline pulsing */
-#ifdef CONFIG_DWC2_TS_DLINE
+#ifdef DWC2_TS_DLINE
usbcfg |= DWC2_GUSBCFG_TERM_SEL_DL_PULSE;
#else
usbcfg &= ~DWC2_GUSBCFG_TERM_SEL_DL_PULSE;
@@ -371,8 +371,8 @@ static void dwc_otg_core_init(struct udevice *dev)
* This programming sequence needs to happen in FS mode before
* any other programming occurs
*/
-#if defined(CONFIG_DWC2_DFLT_SPEED_FULL) && \
- (CONFIG_DWC2_PHY_TYPE == DWC2_PHY_TYPE_FS)
+#if defined(DWC2_DFLT_SPEED_FULL) && \
+ (DWC2_PHY_TYPE == DWC2_PHY_TYPE_FS)
/* If FS mode with FS PHY */
setbits_le32(&regs->gusbcfg, DWC2_GUSBCFG_PHYSEL);
@@ -387,7 +387,7 @@ static void dwc_otg_core_init(struct udevice *dev)
if (readl(&regs->gintsts) & DWC2_GINTSTS_CURMODE_HOST)
init_fslspclksel(regs);
-#ifdef CONFIG_DWC2_I2C_ENABLE
+#ifdef DWC2_I2C_ENABLE
/* Program GUSBCFG.OtgUtmifsSel to I2C */
setbits_le32(&regs->gusbcfg, DWC2_GUSBCFG_OTGUTMIFSSEL);
@@ -407,16 +407,16 @@ static void dwc_otg_core_init(struct udevice *dev)
* immediately after setting phyif.
*/
usbcfg &= ~(DWC2_GUSBCFG_ULPI_UTMI_SEL | DWC2_GUSBCFG_PHYIF);
- usbcfg |= CONFIG_DWC2_PHY_TYPE << DWC2_GUSBCFG_ULPI_UTMI_SEL_OFFSET;
+ usbcfg |= DWC2_PHY_TYPE << DWC2_GUSBCFG_ULPI_UTMI_SEL_OFFSET;
if (usbcfg & DWC2_GUSBCFG_ULPI_UTMI_SEL) { /* ULPI interface */
-#ifdef CONFIG_DWC2_PHY_ULPI_DDR
+#ifdef DWC2_PHY_ULPI_DDR
usbcfg |= DWC2_GUSBCFG_DDRSEL;
#else
usbcfg &= ~DWC2_GUSBCFG_DDRSEL;
#endif
} else { /* UTMI+ interface */
-#if (CONFIG_DWC2_UTMI_WIDTH == 16)
+#if (DWC2_UTMI_WIDTH == 16)
usbcfg |= DWC2_GUSBCFG_PHYIF;
#endif
}
@@ -429,7 +429,7 @@ static void dwc_otg_core_init(struct udevice *dev)
usbcfg = readl(&regs->gusbcfg);
usbcfg &= ~(DWC2_GUSBCFG_ULPI_FSLS | DWC2_GUSBCFG_ULPI_CLK_SUS_M);
-#ifdef CONFIG_DWC2_ULPI_FS_LS
+#ifdef DWC2_ULPI_FS_LS
uint32_t hwcfg2 = readl(&regs->ghwcfg2);
uint32_t hval = (ghwcfg2 & DWC2_HWCFG2_HS_PHY_TYPE_MASK) >>
DWC2_HWCFG2_HS_PHY_TYPE_OFFSET;
@@ -456,14 +456,14 @@ static void dwc_otg_core_init(struct udevice *dev)
brst_sz >>= 1;
}
-#ifdef CONFIG_DWC2_DMA_ENABLE
+#ifdef DWC2_DMA_ENABLE
ahbcfg |= DWC2_GAHBCFG_DMAENABLE;
#endif
break;
case DWC2_HWCFG2_ARCHITECTURE_INT_DMA:
ahbcfg |= DWC2_GAHBCFG_HBURSTLEN_INCR4;
-#ifdef CONFIG_DWC2_DMA_ENABLE
+#ifdef DWC2_DMA_ENABLE
ahbcfg |= DWC2_GAHBCFG_DMAENABLE;
#endif
break;
@@ -476,7 +476,7 @@ static void dwc_otg_core_init(struct udevice *dev)
if (!priv->hnp_srp_disable)
usbcfg |= DWC2_GUSBCFG_HNPCAP | DWC2_GUSBCFG_SRPCAP;
-#ifdef CONFIG_DWC2_IC_USB_CAP
+#ifdef DWC2_IC_USB_CAP
usbcfg |= DWC2_GUSBCFG_IC_USB_CAP;
#endif
@@ -939,9 +939,9 @@ int chunk_msg(struct dwc2_priv *priv, struct usb_device *dev,
debug("%s: msg: pipe %lx pid %d in %d len %d\n", __func__, pipe, *pid,
in, len);
- max_xfer_len = CONFIG_DWC2_MAX_PACKET_COUNT * max;
- if (max_xfer_len > CONFIG_DWC2_MAX_TRANSFER_SIZE)
- max_xfer_len = CONFIG_DWC2_MAX_TRANSFER_SIZE;
+ max_xfer_len = DWC2_MAX_PACKET_COUNT * max;
+ if (max_xfer_len > DWC2_MAX_TRANSFER_SIZE)
+ max_xfer_len = DWC2_MAX_TRANSFER_SIZE;
if (max_xfer_len > DWC2_DATA_BUF_SIZE)
max_xfer_len = DWC2_DATA_BUF_SIZE;
@@ -1198,7 +1198,7 @@ static int dwc2_init_common(struct udevice *dev, struct dwc2_priv *priv)
return -ENODEV;
}
-#ifdef CONFIG_DWC2_PHY_ULPI_EXT_VBUS
+#ifdef DWC2_PHY_ULPI_EXT_VBUS
priv->ext_vbus = 1;
#else
priv->ext_vbus = 0;
diff --git a/drivers/usb/host/dwc2.h b/drivers/usb/host/dwc2.h
index 97a06c48f2..a6f562fe60 100644
--- a/drivers/usb/host/dwc2.h
+++ b/drivers/usb/host/dwc2.h
@@ -759,32 +759,32 @@ struct dwc2_core_regs {
#define RH_B_PPCM 0xffff0000 /* port power control mask */
/* Default driver configuration */
-#define CONFIG_DWC2_DMA_ENABLE
-#define CONFIG_DWC2_DMA_BURST_SIZE 32 /* DMA burst len */
-#undef CONFIG_DWC2_DFLT_SPEED_FULL /* Do not force DWC2 to FS */
-#define CONFIG_DWC2_ENABLE_DYNAMIC_FIFO /* Runtime FIFO size detect */
-#define CONFIG_DWC2_MAX_CHANNELS 16 /* Max # of EPs */
-#define CONFIG_DWC2_HOST_RX_FIFO_SIZE (516 + CONFIG_DWC2_MAX_CHANNELS)
-#define CONFIG_DWC2_HOST_NPERIO_TX_FIFO_SIZE 0x100 /* nPeriodic TX FIFO */
-#define CONFIG_DWC2_HOST_PERIO_TX_FIFO_SIZE 0x200 /* Periodic TX FIFO */
-#define CONFIG_DWC2_MAX_TRANSFER_SIZE 65535
-#define CONFIG_DWC2_MAX_PACKET_COUNT 511
+#define DWC2_DMA_ENABLE
+#define DWC2_DMA_BURST_SIZE 32 /* DMA burst len */
+#undef DWC2_DFLT_SPEED_FULL /* Do not force DWC2 to FS */
+#define DWC2_ENABLE_DYNAMIC_FIFO /* Runtime FIFO size detect */
+#define DWC2_MAX_CHANNELS 16 /* Max # of EPs */
+#define DWC2_HOST_RX_FIFO_SIZE (516 + DWC2_MAX_CHANNELS)
+#define DWC2_HOST_NPERIO_TX_FIFO_SIZE 0x100 /* nPeriodic TX FIFO */
+#define DWC2_HOST_PERIO_TX_FIFO_SIZE 0x200 /* Periodic TX FIFO */
+#define DWC2_MAX_TRANSFER_SIZE 65535
+#define DWC2_MAX_PACKET_COUNT 511
#define DWC2_PHY_TYPE_FS 0
#define DWC2_PHY_TYPE_UTMI 1
#define DWC2_PHY_TYPE_ULPI 2
-#define CONFIG_DWC2_PHY_TYPE DWC2_PHY_TYPE_UTMI /* PHY type */
-#ifndef CONFIG_DWC2_UTMI_WIDTH
-#define CONFIG_DWC2_UTMI_WIDTH 8 /* UTMI bus width (8/16) */
+#define DWC2_PHY_TYPE DWC2_PHY_TYPE_UTMI /* PHY type */
+#ifndef DWC2_UTMI_WIDTH
+#define DWC2_UTMI_WIDTH 8 /* UTMI bus width (8/16) */
#endif
-#undef CONFIG_DWC2_PHY_ULPI_DDR /* ULPI PHY uses DDR mode */
-#define CONFIG_DWC2_PHY_ULPI_EXT_VBUS /* ULPI PHY controls VBUS */
-#undef CONFIG_DWC2_I2C_ENABLE /* Enable I2C */
-#undef CONFIG_DWC2_ULPI_FS_LS /* ULPI is FS/LS */
-#undef CONFIG_DWC2_TS_DLINE /* External DLine pulsing */
-#undef CONFIG_DWC2_THR_CTL /* Threshold control */
-#define CONFIG_DWC2_TX_THR_LENGTH 64
-#undef CONFIG_DWC2_IC_USB_CAP /* IC Cap */
+#undef DWC2_PHY_ULPI_DDR /* ULPI PHY uses DDR mode */
+#define DWC2_PHY_ULPI_EXT_VBUS /* ULPI PHY controls VBUS */
+#undef DWC2_I2C_ENABLE /* Enable I2C */
+#undef DWC2_ULPI_FS_LS /* ULPI is FS/LS */
+#undef DWC2_TS_DLINE /* External DLine pulsing */
+#undef DWC2_THR_CTL /* Threshold control */
+#define DWC2_TX_THR_LENGTH 64
+#undef DWC2_IC_USB_CAP /* IC Cap */
#endif /* __DWC2_H__ */
diff --git a/drivers/usb/host/ehci-omap.c b/drivers/usb/host/ehci-omap.c
index 12c422d811..d5facf10e1 100644
--- a/drivers/usb/host/ehci-omap.c
+++ b/drivers/usb/host/ehci-omap.c
@@ -183,17 +183,8 @@ int omap_ehci_hcd_stop(void)
* Based on "drivers/usb/host/ehci-omap.c" from Linux 3.1
* See there for additional Copyrights.
*/
-#if !CONFIG_IS_ENABLED(DM_USB) || !CONFIG_IS_ENABLED(OF_CONTROL)
-
-int omap_ehci_hcd_init(int index, struct omap_usbhs_board_data *usbhs_pdata,
- struct ehci_hccr **hccr, struct ehci_hcor **hcor)
-{
- *hccr = (struct ehci_hccr *)(OMAP_EHCI_BASE);
- *hcor = (struct ehci_hcor *)(OMAP_EHCI_BASE + 0x10);
-#else
int omap_ehci_hcd_init(int index, struct omap_usbhs_board_data *usbhs_pdata)
{
-#endif
int ret;
unsigned int i, reg = 0, rev = 0;
@@ -304,8 +295,6 @@ int omap_ehci_hcd_init(int index, struct omap_usbhs_board_data *usbhs_pdata)
return 0;
}
-#if CONFIG_IS_ENABLED(DM_USB)
-
static struct omap_usbhs_board_data usbhs_bdata = {
.port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
.port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
@@ -409,5 +398,3 @@ U_BOOT_DRIVER(usb_omap_ehci) = {
.ops = &ehci_usb_ops,
.flags = DM_FLAG_ALLOC_PRIV_DMA,
};
-
-#endif
generated by cgit v1.2.3 (git 2.39.1) at 2025-05-28 15:23:16 +0000