diff options
Diffstat (limited to 'drivers/power/axp209.c')
| -rw-r--r-- | drivers/power/axp209.c | 66 |
1 files changed, 55 insertions, 11 deletions
diff --git a/drivers/power/axp209.c b/drivers/power/axp209.c index 6de5ec6825..67b420910c 100644 --- a/drivers/power/axp209.c +++ b/drivers/power/axp209.c @@ -9,6 +9,16 @@ #include <asm/arch/pmic_bus.h> #include <axp_pmic.h> +#ifdef CONFIG_AXP_ALDO3_VOLT_SLOPE_08 +# define AXP209_VRC_SLOPE AXP209_VRC_LDO3_800uV_uS +#endif +#ifdef CONFIG_AXP_ALDO3_VOLT_SLOPE_16 +# define AXP209_VRC_SLOPE AXP209_VRC_LDO3_1600uV_uS +#endif +#if defined CONFIG_AXP_ALDO3_VOLT_SLOPE_NONE || !defined AXP209_VRC_SLOPE +# define AXP209_VRC_SLOPE 0x00 +#endif + static u8 axp209_mvolt_to_cfg(int mvolt, int min, int max, int div) { if (mvolt < min) @@ -81,8 +91,7 @@ int axp_set_aldo2(unsigned int mvolt) if (rc) return rc; - /* LDO2 configuration is in upper 4 bits */ - reg = (reg & 0x0f) | (cfg << 4); + reg |= AXP209_LDO24_LDO2_SET(reg, cfg); rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg); if (rc) return rc; @@ -99,10 +108,49 @@ int axp_set_aldo3(unsigned int mvolt) return pmic_bus_clrbits(AXP209_OUTPUT_CTRL, AXP209_OUTPUT_CTRL_LDO3); - if (mvolt == -1) - cfg = 0x80; /* determined by LDO3IN pin */ - else + /* + * Some boards have trouble reaching the target voltage without causing + * great inrush currents. To prevent this, boards can enable a certain + * slope to ramp up voltage. Note, this only works when changing an + * already active power rail. When toggling power on, the AXP ramps up + * steeply at 0.0167 V/uS. + */ + rc = pmic_bus_read(AXP209_VRC_DCDC2_LDO3, &cfg); + cfg = AXP209_VRC_LDO3_SLOPE_SET(cfg, AXP209_VRC_SLOPE); + rc |= pmic_bus_write(AXP209_VRC_DCDC2_LDO3, cfg); + + if (rc) + return rc; + +#ifdef CONFIG_AXP_ALDO3_INRUSH_QUIRK + /* + * On some boards, LDO3 has a too big capacitor installed. When + * turning on LDO3, this causes the AXP209 to shutdown on + * voltages over 1.9 volt. As a workaround, we enable LDO3 + * first with the lowest possible voltage. If this still causes + * high inrush currents, the voltage slope should be increased. + */ + rc = pmic_bus_read(AXP209_OUTPUT_CTRL, &cfg); + if (rc) + return rc; + + if (!(cfg & AXP209_OUTPUT_CTRL_LDO3)) { + rc = pmic_bus_write(AXP209_LDO3_VOLTAGE, 0x0); /* 0.7 Volt */ + mdelay(1); + rc |= pmic_bus_setbits(AXP209_OUTPUT_CTRL, + AXP209_OUTPUT_CTRL_LDO3); + + if (rc) + return rc; + } +#endif + + if (mvolt == -1) { + cfg = AXP209_LDO3_VOLTAGE_FROM_LDO3IN; + } else { cfg = axp209_mvolt_to_cfg(mvolt, 700, 3500, 25); + cfg = AXP209_LDO3_VOLTAGE_SET(cfg); + } rc = pmic_bus_write(AXP209_LDO3_VOLTAGE, cfg); if (rc) @@ -131,8 +179,7 @@ int axp_set_aldo4(unsigned int mvolt) if (rc) return rc; - /* LDO4 configuration is in lower 4 bits */ - reg = (reg & 0xf0) | (cfg << 0); + reg |= AXP209_LDO24_LDO4_SET(reg, cfg); rc = pmic_bus_write(AXP209_LDO24_VOLTAGE, reg); if (rc) return rc; @@ -153,10 +200,7 @@ int axp_init(void) if (rc) return rc; - /* Low 4 bits is chip version */ - ver &= 0x0f; - - if (ver != 0x1) + if ((ver & AXP209_CHIP_VERSION_MASK) != 0x1) return -EINVAL; /* Mask all interrupts */ |