diff options
Diffstat (limited to 'drivers/ddr/imx/imx8m/ddr_init.c')
| -rw-r--r-- | drivers/ddr/imx/imx8m/ddr_init.c | 72 |
1 files changed, 72 insertions, 0 deletions
diff --git a/drivers/ddr/imx/imx8m/ddr_init.c b/drivers/ddr/imx/imx8m/ddr_init.c index de302937d0..664966c41b 100644 --- a/drivers/ddr/imx/imx8m/ddr_init.c +++ b/drivers/ddr/imx/imx8m/ddr_init.c @@ -21,6 +21,76 @@ void ddr_cfg_umctl2(struct dram_cfg_param *ddrc_cfg, int num) } } +#ifdef CONFIG_IMX8M_DRAM_INLINE_ECC +void ddrc_inline_ecc_scrub(unsigned int start_address, + unsigned int range_address) +{ + unsigned int tmp; + + /* Step1: Enable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000000); + /* Step2: Set ECCCFG1.ecc_parity_region_lock to 1 */ + reg32setbit(DDRC_ECCCFG1(0), 0x4); + /* Step3: Block the AXI ports from taking the transaction */ + reg32_write(DDRC_PCTRL_0(0), 0x0); + /* Step4: Set scrub start address */ + reg32_write(DDRC_SBRSTART0(0), start_address); + /* Step5: Set scrub range address */ + reg32_write(DDRC_SBRRANGE0(0), range_address); + /* Step6: Set scrub_mode to write */ + reg32_write(DDRC_SBRCTL(0), 0x00000014); + /* Step7: Set the desired pattern through SBRWDATA0 registers */ + reg32_write(DDRC_SBRWDATA0(0), 0x55aa55aa); + /* Step8: Enable the SBR by programming SBRCTL.scrub_en=1 */ + reg32setbit(DDRC_SBRCTL(0), 0x0); + /* Step9: Poll SBRSTAT.scrub_done=1 */ + tmp = reg32_read(DDRC_SBRSTAT(0)); + while (tmp != 0x00000002) + tmp = reg32_read(DDRC_SBRSTAT(0)) & 0x2; + /* Step10: Poll SBRSTAT.scrub_busy=0 */ + tmp = reg32_read(DDRC_SBRSTAT(0)); + while (tmp != 0x0) + tmp = reg32_read(DDRC_SBRSTAT(0)) & 0x1; + /* Step11: Disable SBR by programming SBRCTL.scrub_en=0 */ + clrbits_le32(DDRC_SBRCTL(0), 0x1); + /* Step12: Prepare for normal scrub operation(Read) and set scrub_interval*/ + reg32_write(DDRC_SBRCTL(0), 0x100); + /* Step13: Enable the SBR by programming SBRCTL.scrub_en=1 */ + reg32_write(DDRC_SBRCTL(0), 0x101); + /* Step14: Enable AXI ports by programming */ + reg32_write(DDRC_PCTRL_0(0), 0x1); + /* Step15: Disable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000001); +} + +void ddrc_inline_ecc_scrub_end(unsigned int start_address, + unsigned int range_address) +{ + /* Step1: Enable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000000); + /* Step2: Block the AXI ports from taking the transaction */ + reg32_write(DDRC_PCTRL_0(0), 0x0); + /* Step3: Set scrub start address */ + reg32_write(DDRC_SBRSTART0(0), start_address); + /* Step4: Set scrub range address */ + reg32_write(DDRC_SBRRANGE0(0), range_address); + /* Step5: Disable SBR by programming SBRCTL.scrub_en=0 */ + clrbits_le32(DDRC_SBRCTL(0), 0x1); + /* Step6: Prepare for normal scrub operation(Read) and set scrub_interval */ + reg32_write(DDRC_SBRCTL(0), 0x100); + /* Step7: Enable the SBR by programming SBRCTL.scrub_en=1 */ + reg32_write(DDRC_SBRCTL(0), 0x101); + /* Step8: Enable AXI ports by programming */ + reg32_write(DDRC_PCTRL_0(0), 0x1); + /* Step9: Disable quasi-dynamic programming */ + reg32_write(DDRC_SWCTL(0), 0x00000001); +} +#endif + +void __weak board_dram_ecc_scrub(void) +{ +} + int ddr_init(struct dram_timing_info *dram_timing) { unsigned int tmp, initial_drate, target_freq; @@ -169,6 +239,8 @@ int ddr_init(struct dram_timing_info *dram_timing) reg32_write(DDRC_PCTRL_0(0), 0x00000001); debug("DDRINFO: ddrmix config done\n"); + board_dram_ecc_scrub(); + /* save the dram timing config into memory */ dram_config_save(dram_timing, CONFIG_SAVED_DRAM_TIMING_BASE); |